User manual 3COM U200-M/A 2-PORT 10/100/1000 MODULE

[. . . ] H3C SecPath U200 Series Unified Threat Management Products Installation Manual Hangzhou H3C Technologies Co. , Ltd. http://www. h3c. com Manual Version: 5PW101-20090520 Copyright © 2009, Hangzhou H3C Technologies Co. , Ltd. and its licensors All Rights Reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Hangzhou H3C Technologies Co. , Ltd. Trademarks H3C, , Aolynk, , H3Care, , TOP G, , IRF, NetPilot, Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V2G, VnG, PSPT, XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou H3C Technologies Co. , Ltd. All other trademarks that may be mentioned in this manual are the property of their respective owners. Notice The information in this document is subject to change without notice. [. . . ] For the detailed description about software maintenance through the Web interface, refer to "Upgrading the Signature Database and Maintaining Configuration Files" on page 6-34. In the CLI approach, the following two methods are available for software upgrading: Upgrade BootWare and applications using the Xmodem protocol through a serial interface. Upgrade applications using TFTP/FTP through Ethernet interface on BootWare menu or through command lines. The BootWare program is upgraded together with the Comware application. You do not need to upgrade the BootWare separately. The system automatically upgrades the BootWare program to the latest version if the current BootWare version is found to be inconsistent with the BootWare version contained in the host application. Check the current version of the BootWare and the Comware application before upgrading them. For the association between the Comware application version and the BootWare program version, refer to the version configuration information in Release Notes. 6-3 Figure 6-1 BootWare and Comware programs upgrade flow Start Comware application N Upgrade Comware ?Y Choose the right Comware application file Choose an upgrade method Through Ethernet interface Xmodem TFTP FTP Upgrade End BootWare Menu BootWare Main Menu When the device is powered on, the system first initializes the memory. After the initialization, the system, the U200-A for example, runs the extended BootWare, and the following information is displayed on the console terminal: The information displayed on the terminal may vary with different BootWare versions. System is starting. . . Booting Normal Extend BootWare. . . . ************************************************************************** * * * ************************************************************************** H3C SecPath UTM200-A BootWare, Version 1. 10 * * * 6-4 Copyright (c) 2004-2008 Hangzhou H3C Technologies Co. , Ltd. Compiled Date CPU Type CPU L1 Cache CPU Clock Speed Memory Type Memory Size Memory Speed BootWare Size Flash Size CPLD Version PCB Version : May 7 2008 : XLS208 : 32KB : 750MHz : DDR2 SDRAM : 1024MB : 533MHz : 1536KB : 32MB : 1. 0 : Ver. A BootWare Validating. . . Press Ctrl+B to enter extended boot menu. . . Press Ctrl+B to enter the extended BootWare menu; otherwise, the system enters the self extraction process of applications. You must press Ctrl+B in four seconds when "Press Ctrl+B to enter extended boot menu" appears. Otherwise, the system will read and decompress the application file instead of entering the extended BootWare menu. After the system enters the self extraction process of applications, if you want to enter the extended BootWare menu, you need to reboot the device. The extended BootWare menu is referred to as BootWare main menu in this manual unless otherwise specified. Press Ctrl+B when "Press Ctrl+B to enter extended boot menu. . . " appears. The system displays: Please input BootWare password: You can try up to three times to enter the correct BootWare password (the initial password is null). If you fail to provide the correct password with three attempts, you need to reboot the system. After you type the correct password, the system enters the BootWare main menu: Note: The current operating device is cfa0 Enter < Storage Device Operation > to select device. ==================<EXTEND-BOOTWARE MENU>===================== | <1> Boot System | <2> Enter Serial SubMenu | <3> Enter Ethernet SubMenu | <4> File Control | <5> Modify BootWare Password | <6> Skip Current System Configuration | | | | | | 6-5 | <7> BootWare Operation Menu | <8> Clear Super Password | <9> Storage Device Operation | <0> Reboot | | | | ============================================================= Enter your choice(0-9): The menu is described in the following table. Table 6-1 BootWare main menu Menu item <1> Boot System <2> Enter Serial SubMenu <3> Enter Ethernet SubMenu <4> File Control <5> Modify BootWare Password <6> Skip Current System Configuration <7> BootWare Operation Menu Description Boot the system application from the CF card Enter the serial submenu. Refer to the "Serial Submenu" section on page 6-6. Refer to the "Ethernet Submenu" section on page 6-7. Refer to the "File Control Submenu" section on page 6-8. Boot the system with the system configuration ignored. [. . . ] Der Querschnitt der Erdverbindung sollte mindestens 1. 0mm2 betragen. / 1. 0mm2 For AC supplied model: The device applies to TN power systems. Mit Wechselstrom betriebenes Modell: Das Gerät arbeitet mit einem Phase-Nullleiter-System. AC TN For DC supplied model: The device applies to DC power source that complies with the Safety Extra-Low Voltage (SELV) requirements in IEC 60950 based safety standards. [. . . ]