User manual 3M ACCUGLIDE TAPING HEADS

[. . . ] And now there are pluses: · Low profile side plate for faster, easier threading · Open tape path for faster, easier threading · Light weight for easy handling and removal · Easy-to-follow instructional labeling to clearly show tape path · Buffing and applying rollers designed for easy removal · Available in stainless steel Tape drum latch · Secures roll for stability and positive tape alignment · Press to release for easy roll change Friction brake drum · Maintains proper tape tension and prevents overcoasting for smooth, secure tape application Rugged construction · Epoxy powder coated steel for durability. Performed to specifications for over 3. 5 million cycles in testing. For use in high-moisture and corrosive environments AccuGlideTM Taping Head 2+ Specifications: Case Size Capability: Size: Min Max Length 6" (150mm) Unlimited Width 6" (150mm) Unlimited Height 4. 75" (121mm) Unlimited 3. 5" (90mm) with optional 2" (50mm) leg length Operating Rate: Conveyor speeds up to 80 ft. /min. (25m/min. ) Taping Head Dimensions (without tape roll bracket): 2" Head 3" Head Length 15. 75" (400mm) 15. 75" (400mm) Width 4. 2" (105mm) 5. 2" (130mm) Height 14. 25" (365mm) 14. 25" (365mm) Weight: Packaged­ 17 lbs. [. . . ] (25m/min. ) Taping Head Dimensions (without tape roll bracket): 2" Head 3" Head Length 15. 75" (400mm) 15. 75" (400mm) Width 4. 2" (105mm) 5. 2" (130mm) Height 14. 25" (365mm) 14. 25" (365mm) Weight: Packaged­ 17 lbs. (7, 3 kg) Note: 1) Case size minimums and maximums may also be determined by the case conveying system used. 2) Cases must meet accepted industry standards. 3) Cases must be properly filled (not underpacked or overpacked). Tape: For use with 3M brand pressure-sensitive film box sealing tapes. Width: 1. 5 inches [36mm] minimum to 2" or 48mm maximum for AccuGlideTM taping heads. 2" or 48mm minimum to 3" or 72 maximum for 3" AccuGlideTM taping heads. Tape roll diameter: up to 16" [405 mm] maximum on a 3" [75mm] diameter core. 3M sells its AccuGlideTM Powered Taping Head with the following warranties: A. The Taping Head knife blades, springs and rollers will be free from all defects for ninety (90) days after delivery. All other Taping Head parts contained in the drive assembly will be free from all defects for three (3) years after delivery. The motor and transmission will be free from all defects for ninety (90) days after delivery. All other parts of the drive assembly will be free from all defects for ninety (90) days after delivery. If any part is proved to be defective within the warranty period, then the exclusive remedy and 3M's sole option, to repair or replace the part, provided the defective part is returned immediately to 3M's factory or an authorized service station designated by 3M. A part will be presumed to have become defective after the warranty period unless the part is received or 3M is notified of the problem no later than five (5) calendar days after the warranty period. If 3M is unable to repair or replace the part within a reasonable time, then 3M, at its option, will replace the equipment or refund the purchase price. [. . . ] A part will be presumed to have become defective after the warranty period unless the part is received or 3M is notified of the problem no later than five (5) calendar days after the warranty period. If 3M is unable to repair or replace the part within a reasonable time, then 3M, at its option, will replace the equipment or refund the purchase price. 3M shall have no obligation to provide or pay for the labor required to install repaired or replacement parts. [. . . ]