User manual 3M FASTBOND CONTACT ADHESIVE BROCHURE

[. . . ] 3 Fastbond Water-based Adhesives TM Take to the water for productivity, performance, profitability, compliance For your continued success. . . [. . . ] User should test for specific application suitability. After only one-minute, 3M TM Fastbond TM Contact Adhesive 2000NF reaches 50 psi on a birch-to-birch overlap bond. 7 3MTM FastbondTM Foam Adhesive 100 Fast-tacking contact adhesive to hold seams and curves in seconds Spray one-part 3MTM FastbondTM Foam Adhesive 100 to bond foam to foam and fiber fill, foam to wood, fiber fill to fabric, and more in bedding, furniture, upholstery, and other applications. Hold foam to foam in 15 seconds or bond immediately when used with activator. 8 · 20-minute bonding range for repositioning after initial tack to meet various assembly requirements · Foam-tearing strength after complete setting (foam fails before the bond line) · High solids for more economical use of adhesive (up to 4x more coverage than a typical solvent-based product) · Non-dimpling, soft bond line for finished product aesthetics and a smoother, more comfortable feel · Spray at low pressure to reduce misting and overspray Photo courtesy of Four Seasons Mfg. 9 10 TM 11 TM 12 For easy bullnose fabrication in a compound cushion, 3M Fastbond Foam Adhesive 100 bonds a lighter density foam around a higher density core. High tack holds in seconds. Heat Resistance (°F) 0 3M Fastbond Foam Adhesive 100 TM TM 50 100 150 200 250 250 Typical Water-based Foam Adhesive (Natural Rubber) Latex Typical Non-Flammable Foam Adhesive (Chlorinated) Typical Flammable Foam Adhesive 13 200 175 90 Neoprene-based formulation bonds leather to foam with foam-tearing strength and a soft bond line that complements the leather's suppleness. Basis: Two spray applied knife edge pinch bonds were made with 1. 2 lb/cu ft density polyurethane foam cut into 4 inch cubes, one 4" x 4" face of each foam cube was bonded to itself 30 seconds after application using approximately 5 seconds of manually applied hand and finger pressure, the bonded foam cubes were then dried 24 hours at 70°F ambient conditions, the bonded specimens then placed in a heated oven for a period of 24 hours at various temperatures. Heat resistance, as indicated here, is the highest temperature measured at which the seams of both specimens held together and showed no visual evidence of failure anywhere along the seams. 3MTM FastbondTM Insulation Adhesive 49 One surface, pressure sensitive formulation for speed and convenience 3MTM FastbondTM Insulation Adhesive 49 is a fast tacking, pressure sensitive formulation for bonding fabric, insulation, and other lightweight materials to themselves, or to metal, wood, and other substrates. Spray, roll, or brush to only one surface and cut time to half that of two surface applications. 15 14 With instant tack and high coverage, bonding insulation into HVAC systems, appliances, and walk-in coolers is easy and economical. 16 · Sticks instantly like tape with strength enough for immediate shipping · Long bonding range of up to 30 days for delayed assembly · High solids for more economical use of adhesive with proprietary chemistry to help reduce adhesive consumption · Low viscosity for simple dispensing with low maintenance systems · UL component recognition MAGW2 file MH 6288 Reduction in Gallons Customers A B C D E F G H I J K 10 % Reduction in Gallons Consumed 20 30 40 50 60 70 80 90 100 8, 600 8, 000 12, 500 2, 100 8, 200 5, 800 145 10, 800 10, 000 50, 000+ 9, 000 Gallons Saved In this graph, no matter if the account is big like J or small like G, they save more than 50% in adhesive consumption. This data was gathered by follow-up visits to customers who recently switched to 3MTM FastbondTM Adhesive 49. Each customer had a similar application of bonding insulation for HVAC. Coverage may vary on a given application. [. . . ] (2) Canvas to cold rolled steel @ 2. 0 inches/minute separation rate. Insulation and Carpet Adhesives Product/ Color Insulation Adhesive 49/Clear Solids Weight (Approx. ) 55% Flash Point (Closed Cup) Consistency None Thin Application Method Spray, brush, roller Bonding Range 30 days plus Peel Strength (PIW) 75°F (24°C) Packaging 3. 0 (1) 5-gallon box and pail, drum, tote Description · Fast tacking, high performance pressure sensitive adhesive for lightweight materials · Low VOCs · UL component recognition MAGW2 file MH 6288 Pressure · Permanently pressure sensitive with Sensitive aggressive tack Adhesive · Plasticizer resistant 4224NF/ · Low VOC content Blue and clear (1) Primed polyester to steel @ 2. 0 inches/minute separation rate. 40% None Thick liquid Spray, 30 days brush, roller, plus trowel, coater 4. 4 (1) 5-gallon pail, drum Note: The technical information and data on these pages should be considered representative or typical only, and should not be used for specification purposes. PRODUCT USE: All statements, technical information and recommendations contained in this document are based upon tests or experience that 3M believes are reliable. [. . . ]