User manual 3M MP8750

[. . . ] MP8750 Multimedia Projector Operator's Guide Projecteur multimédia MP8750 Guide d'utilisation MP8750 Multimedia-Projektor Bedienerhandbuch Proyector de medios múltiples (multimedia) MP8750 Guía del operador Guida dell'operatore del proiettore multimediale MP8750 Bruksanvisning för MP8750 Multimediaprojektor 3M MP8750 Multimediaprojector Gebruiksaanwijzing MP8750 Table of Contents SAFEGUARDS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . II WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IV SECTION 1: UNPACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CONTENTS OF SHIPPING BOX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . KEEP YOUR PACKING MATERIALS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Power up your computer and video source(s). ü Note In most cases, the projector will automatically adjust to the graphic mode of your computer by selecting a pre-programmed setting. © 3M 1999 3MTM Multimedia Projector MP8750 7 4-2. Standby Mode When the projector is not being used, place it into standby mode. The lamp will switch off and the red LED will illuminate. ü Note The fan motor will continue to run for a few minutes until the projector cools down and then the fan will turn off. Press the Standby button again to illuminate the lamp and project an image on the screen. 4-3. Press the Standby button to place the projector in the standby mode (red LED illuminates). Wait until the cooling fan motor cycles off and the lamp LED turns off. ü Note Switching the main power off before the fan has cycled off will decrease the life of the projection lamp. Turn off the power to your input devices. Install lens cap to protect projection lens. To transport the projector, disconnect all power and connection cables. 4-4. Using System Menus Main Menu: Press the Menu button on the operator touch panel keypad (Figure 3-3) or the remote control keypad (Figure 5-1) to display the Main Menu. (1) Main Menu The menu name (1) is on the top line. (2) Picture An arrowhead (2) at the right of a menu line indicates (4) Audio that this item is a sub-menu that can be selected. Tools Signal source User Interface Advanced Setup Info PC/RGB1 (3) A text field (3) at the right of a line indicates that this is a value that you can change in a drop down window. Info: Press Enter to display the Info window. To select a sub-menu, press the Disc Pad up or down to highlight (select) the desired sub-menu (4). Then press the Disc Pad to the right or the Enter button to display the sub-menu (see Sub-Menu). To change a text field value, press the Disc Pad up or down to highlight (select) the menu line (3). Then press the Disc Pad to the right or the Enter button to display a drop down window of all the possible values. Use the Disc Pad to select a value and press Enter to initiate the selection. To exit a sub-menu, press the Disc Pad to the left. To completely exit the menu system and return to the projected image, press the Menu button. 8 3MTM Multimedia Projector MP8750 © 3M 1999 Sub-Menu: Select the desired sub-menu (see Main Menu). Press the Disc Pad to the right or the Enter button to display the sub-menu. Picture (1) The sub-menu name (1) is on the top line. A slider bar (2) at the right of a sub-menu line indicates you can increase or decrease the value. A number field (3) at the right of a sub-menu line indicates that you can change it. [. . . ] VCR connected to · aerial system and to projector. · The factory default settings of the projector can be restored by pressing Enter and Mute simultaneously on the control panel when switching on the main power switch of the projector and pressing the Standby button afterwards. The projector will start immediately and the message " Parameter factory settings restored" displayed in the starting screen will indicate the default settings are reset. 7-2. Service Information For product information, product assistance, service information, or to order accessories or spare parts, please call: In U. S. [. . . ]