User manual 3R SYSTEM CASE R234

[. . . ] p Do not place any sources of danger on the apparatus (e. g. liquid filled objects, lighted candles). q This product may contain lead and mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www. eiae. org. r Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. Warning • • • • • Never remove the casing of this apparatus. Never lubricate any part of this apparatus. [. . . ] Keep this apparatus away from direct sunlight, naked flames or heat. Ensure that you always have easy access to the power cord, plug or adaptor to disconnect the apparatus from the power. Notice This product complies with the radio interference requirements of the European Community. This product complies with the requirements of the following directives and guidelines: 2004/108/EC + 2006/95/EC Any changes or modifications made to this device that are not expressly approved by Philips Consumer Lifestyle may void the user’s authority to operate the equipment. Recycling Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. When you see the crossed-out wheel bin symbol attached to a product, it means the product is covered by the European Directive 2002/96/EC: Never dispose of your product with other household waste. Please inform yourself about the local rules on the separate collection of electrical and electronic products. The correct disposal of your old product helps prevent potentially negative consequences on the environment and human health. Your product contains batteries covered by the European Directive 2006/66/EC, which cannot be disposed of with normal household waste. Please inform yourself about the local rules on separate collection of batteries. The correct disposal of batteries helps prevent potentially negative consequences on the environment and human health. Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet. ) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment. 2 Press AUTOSCAN to activate the program mode. » The preset number begins to blink. 5 Repeat the above steps to program other stations. Note • To overwrite a programmed station, store another station in its place. Select a preset radio station 1 Press - PRESET + to select a preset number. 5 1 2 3 4 5 Other features Ensure that you have set the clock correctly. In standby mode, rotate SET ALARM/CLOCK/SET TIME to the SET ALARM position. » The hour and minute digits begin to blink. Rotate the SET ALARM/CLOCK/SET TIME to the CLOCK position to confirm. Set the alarm timer Set alarm mode 1 Adjust the BUZZER/RADIO ALARM control to select the source for the alarm. » When the alarm time comes, the selected FM/MW radio or buzzer turns on. Tip • If radio source is selected, you can adjust MW/FM to select between FM and MW radio. • To adjust volume for the tuner source, exit the alarm mode first. Activate and deactivate the alarm timer 1 Press ALARM ON/OFF repeatedly to activate or deactivate the alarm timer. Repeat alarm 1 When the alarm rings, press REPEAT ALARM/BRIGHTNESS CONTROL. » The alarm repeats ringing minutes later. Tip • You can press TUNING+/- to adjust interval to repeat alarm. Stop alarm sound 1 When the alarm rings, press SLEEP/ALARM RESET. » The alarm stops but the alarm settings remain. Set the sleep timer This unit can switch to standby automatically after a set period of time. 1 Press SLEEP repeatedly to select a set period of time (in minutes). » When the sleep timer is activated, the display shows . [. . . ] To deactivate sleep timer 1 Press SLEEP repeatedly until [OFF] (off) is displayed. disappears on the » When the sleep timer is deactivated, display. Adjust display brightness 1 Press REPEAT ALARM/BRIGHTNESS CONTROL repeatedly to select different levels of display brightness. 6 Product information Note • Product information is subject to change without prior notice. Specifications Amplifier Rated Output Power 0. 2W RMS Tuner Tuning Range Tuning grid FM: 87. 5 - 108 MHz MW: 531-1602 KHz FM: 50 KHz MW: 9KHz Sensitivity FM: <22 dBu - Mono, 26dB S/N Ratio MW: <92 uV/m Search Selectivity Total Harmonic Distortion Signal to Noise Ratio FM: <28 dBu MW:<98 uV/m FM: <3% MW:<5% FM: >45 dB MW:>40 dB General information AC power Operation Power Consumption Standby Power Consumption Dimensions Weight 220 ~240 V, 50/60Hz <5W <2W 172 x 92 x 72 mm 0. 56 kg 7 Troubleshooting Warning • Never remove the casing of this apparatus. To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this apparatus, check the following points before requesting service. If the problem remains unsolved, go to the Philips web site (www. philips. com/support). [. . . ]