User manual AASTRA DIALOG 4225 VISION

[. . . ] Dialog 4223 Professional/Dialog 4225 Vision System Telephones for MX-ONETM Telephony System and MD110 User Guide North American Function Codes Are Used in This Guide Cover Page Graphic Place the graphic directly on the page, do not care about putting it in the text flow. Select Graphics > Properties and make the following settings: · · · · Width: 15, 4 cm (Important!) Height: 11, 2 cm (May be smaller) Top: 5, 3 cm (Important!) Left: -0, 3 cm (Important!) This text should then be hidden. AE/LZT 103 68 R5A © Aastra Telecom Sweden AB 2008. All rights reserved. Table of Contents Table of Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Note: If your phone is programmed with "Multiple Directory Diversion and Do Not Disturb" (ask your system administrator), Diversion is ordered and cancelled simultaneously on all lines. Dialog 4223 Professional/Dialog 4225 Vision 63 Call Forwarding Order Direct Diversion from your own extension The call can be diverted to an individual position or up to three predetermined common answering positions (depending on the type of the incoming call). Programmed by your system administrator. Note: Diversion can also be ordered and cancelled from the answering position, use the same procedure as in section "Internal Follow-me" on page 67. Press, Note: The function key is preprogrammed by your system administrator. If you order Diversion with the handset off hook or the loudspeaker on, press the Diversion key twice. or Diversion Ô Absence Down or Up Activate Exit press (see display). Press to frame Direct Diversion to nnnn (see display). (nnnn = number to the answering position, e. g. Note: You can also use the following procedure to activate: dial and press the Clear key. *2# Diversion ÕÔ Cancel Direct Diversion from your own extension Press, Note: The function key is preprogrammed by your system administrator. or NoDiversion press (see display). Note: You can also use the following procedure to cancel: dial and press the Clear key. #2# 64 Dialog 4223 Professional/Dialog 4225 Vision Call Forwarding Diversion when there is no answer Order: Absence Down or Up Press (see display). Press to frame Div on no answer to nnnn: Not active (see display). (nnnn = number to the answering position, e. g. The incoming call is diverted after 3 signals. Note: You can also use the following procedure to activate: dial (and press the Clear key. Activate Exit *21# Cancel: Absence Down or Up Press (see display). Press to frame Div on no answer to nnnn: Active (see display). (nnnn = number to the answering position, e. g. Note: You can also use the following procedure to cancel: dial and press the Clear key. Deactivate Exit #21# Dialog 4223 Professional/Dialog 4225 Vision 65 Call Forwarding Diversion when caller receives a busy tone Order: Absence Down or Up Press (see display). Press to frame Div on busy to nnnn: Not active (see display). (nnnn = number to the answering position, e. g. Note: You can also use the following procedure to activate: dial and press the Clear key. Activate Exit *22# Cancel: Absence Down or Up Deactivate Exit Press (see display). Press to frame Div on busy to nnnn: Active (see display). [. . . ] The display shows the firmware revision state and Selftest OK for a few seconds. If there is something wrong, a fault message appears. Inform your system administrator about the fault message. All the key lamps on the phone and connected extra key panels should be switched on during the self-test to indicate that each key lamp is OK. [. . . ]