User manual ABIT IC7-G

[. . . ] IC7-G Socket 478 System Board User's Manual 4200-0351-02 Rev. 1. 00 Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. [. . . ] AGP Data Rate Capability: This item selects the data transfer rate of AGP device. A higher rate delivers faster and better graphics to your system. Make sure your graphics card supports the mode you select. User's Manual 3-12 Chapter 3 3-5. Integrated Peripherals OnChip IDE Device: Click <Enter> key to enter its submenu: IDE HDD Block Mode: This item determines to use the Block Mode for IDE HDD. [Enabled]: The IDE HDD supports block mode. [Disabled]: The IDE HDD supports standard mode. OnChip IDE-1 Controller: This item allows you to enable or disable the primary and secondary IDE controller. Select [Disabled] if you want to add a different hard drive controller. Master/Slave Drive PIO Mode The PIO (Programmed Input/Output) mode allows the BIOS to tell the controller what it wants and then let the controller and the CPU perform the complete task, rather than having the BIOS issue a series of commands to affect a transfer to or from the disk drive. [Auto]: The BIOS will select the best available mode after checking your disk drive. IC7-G BIOS Setup 3-13 [Mode 0-4]: You can select a mode that matches your disk drive's timing. Do not use the wrong setting or you will have drive errors. Master/Slave Drive Ultra DMA This item allows you to set the Ultra DMA in use. [Auto]: The BIOS will select the best available option after checking your hard drive or CD-ROM. [Disabled]: The BIOS will not detect these categories. If problem arises in using Ultra DMA devices, try disabling this item. OnChip IDE-2 Controller: The description is same as the OnChip IDE-1 Controller. OnChip Serial ATA: This option enables or disables the SATA controller of ICH5R South Bridge. Serial ATA 1 Mode / Serial ATA 2 Mode: This item determines the function mode for Serial ATA Port 1 (i. e. The SATA1 connector in this model) and Serial ATA Port 2 (i. e. Both SATA1 and SATA2 will be served each as one single IDE connector after selected as the following modes: Serial ATA Port 1 (SATA1) Mode 1 IDE-1 Master Serial ATA Port 2 Description (SATA2) · SATA1 serves as IDE-1 Master IDE-1 Slave · SATA2 serves as IDE-1 Slave · OnChip IDE-1 controller disabled · SATA1 serves as IDE-1 Slave IDE-1 Master · SATA2 serves as IDE-1 Master · OnChip IDE-1 controller disabled · SATA1 serves as IDE-2 Master IDE-2 Slave · SATA2 serves as IDE-2 Slave · OnChip IDE-2 controller disabled · SATA1 serves as IDE-2 Slave IDE-2 Master · SATA2 serves as IDE-2 Master · OnChip IDE-2 controller disabled · SATA1 serves as IDE-1 Logical IDE-2 · SATA2 serves as IDE-2 · OnChip IDE-1 and IDE-2 controller disabled · SATA1 serves as IDE-2 Logical IDE-1 · SATA2 serves as IDE-1 · OnChip IDE-1 and IDE-2 controller disabled · SATA1 serves as IDE-3 Master IDE-4 Master · SATA2 serves as IDE-4 Master · OnChip IDE-1 and IDE-2 controller enabled · SATA1 serves as IDE-4 Master IDE-3 Master · SATA2 serves as IDE-3 Master · OnChip IDE-1 and IDE-2 controller enabled Mode 2 IDE-1 Slave Mode 3 IDE-2 Master Mode 4 IDE-2 Slave Mode 5 Logical IDE-1 Mode 6 Logical IDE-2 Mode 7 IDE-3 Master Mode 8 IDE-4 Master User's Manual 3-14 Chapter 3 RAID Function: This option enables or disables the SATA RAID function of ICH5R South Bridge. ATTENTION: This item is only available when both the items "Serial ATA 1 Mode" and "Serial ATA 2 Mode" are selected as [IDE-3 Master] / [IDE-4 Master] or [IDE-4 Master] / [IDE-3 Master]. OnChip PCI Device: Click <Enter> key to enter its submenu: OnChip USB Controller: This option enables or disables the USB controller. [. . . ] However, we will try to do our best to help every customer. Please also remember that for many of our technical support team English is a second language, you will have a better chance of getting a helpful answer if your question can be understood in the first place. Be sure to use very, simple, concise language that clearly states the problem, avoid rambling or flowery language and always list your system components. Here is the contact information for our branch offices: IC7-G How to Get Technical Support J-3 North America and South America: ABIT Computer (U. S. A. ) Corporation 45531 Northport Loop West, Fremont, California 94538, U. S. A. [. . . ]