User manual ABIT LG-95

[. . . ] Hardware Setup BIOS Setup Driver & Utility Multilingual QIG LG-95 LG-95Z Motherboard Socket 775 Intel Core 2 Duo* / Pentium Dual-Core / Pentium D / Pentium 4 / Celeron D Intel 945G (945GZ)* / ICH7 FSB1066 (800)* DDR2 667 (533)* Integrated Intel GMA 950 Gigabit LAN (10/100)* Appendix 4x SATA 3. 0Gb/s 7. 1 Channel HD Audio Vista Premium HW Ready * See the "Specifications" of each model for details. LG-95/LG-95Z User's Manual English + Multilingual QIG 1st Edition, December 2006 Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. Product names appearing in this manual are for identification purpose only and trademarks and product names or brand names appearing in this document are the property of their respective owners. [. . . ] A higher fan speed will be helpful for better airflow and heat-dissipation. Nevertheless, stay alert to touch any heatsink since the high temperature generated by the working system is still possible. 1-12 LG-95/LG-95Z Hardware Setup 1. 7. 2 DDR2/DDR Memory Slots This motherboard supports two DDR or two DDR2 DIMMs. Note that DDR & DDR2 cannot be both applied at the same time. Apply either DDR or DDR2 memory modules only! Usually there is no hardware or BIOS setup required after adding or removing memory modules, but you will have to clear the CMOS memory first if any memory module related problem occurs. To install system memory: 1. Power off the computer and unplug the AC power cord before installing or removing memory modules. Hold two edges of the DIMM module carefully, keep away from touching its connectors. Align the notch key on the module with the rib on the slot. Firmly press the module into the slots until the ejector tabs at both sides of the slot automatically snap into the mounting notch. Do not force the DIMM module in with extra force as the DIMM module only fits in one direction. To remove the DIMM modules, push the two ejector tabs on the slot outward simultaneously, and then pull out the DIMM module. Static electricity can damage the electronic components of the computer or optional boards. Before starting these procedures, ensure that you are discharged of static electricity by touching a grounded metal object briefly. 2. LG-95/LG-95Z 1-13 1. 8 Connecting Peripheral Devices 1. 8. 1 Floppy and IDE Disk Drive Connectors The FDC1 connector connects up to two floppy drives with a 34-wire, 2-connector floppy cable. Connect the single end at the longer length of ribbon cable to the FDC1 on the board, the two connectors on the other end to the floppy disk drives connector. Generally you need only one floppy disk drive in your system. The red line on the ribbon cable must be aligned with pin-1 on both the FDC1 port and the floppy connector. Each of the IDE port connects up to two IDE drives at Ultra ATA/100 mode by one 40-pin, 80-conductor, and 3-connector Ultra ATA/66 ribbon cables. Connect the single end (blue connector) at the longer length of ribbon cable to the IDE port of this board, the other two ends (gray and black connector) at the shorter length of the ribbon cable to the connectors of your hard drives. Make sure to configure the "Master" and "Slave" relation before connecting two drives by one single ribbon cable. The red line on the ribbon cable must be aligned with pin-1 on both the IDE port and the hard-drive connector. 1-14 LG-95/LG-95Z Hardware Setup 1. 8. 2 Serial ATA Connectors Each SATA connector serves as one single channel to connect one SATA device by SATA cable. To connect SATA device: 1. Attach either end of the signal cable to the SATA connector on motherboard. Attach the SATA power cable to the SATA device and connect the other end from the power supply. The motherboard in this illustration is served for DEMO only, may not be the same type or model as the one described in this user's manual. 2. LG-95/LG-95Z 1-15 1. 8. 3 Additional USB 2. 0 Port Headers Each header supports 2x additional USB 2. 0 ports by connecting bracket or cable to the rear I/O panel or the front-mounted USB ports of your chassis. Pin 1 3 5 7 Pin Assignment VCC Data0 Data0 + Ground Pin 2 4 6 8 10 Pin Assignment VCC Data1 Data1 + Ground NC Make sure the connecting cable bears the same pin assignment. 1. 8. 4 Internal Audio Connectors This connector connects to the audio output of internal CD-ROM drive or add-on card. 1-16 LG-95/LG-95Z Hardware Setup 1. 8. 5 Front Panel Audio Connection Header This header provides the connection to audio connector at front panel. Pin 1 2 3 4 5 6 7 8 9 10 Signal Name PORT1 L GND PORT1 R PRESENCE# PORT2 R SENSE1_RETURN SENSE_SEND Key PORT2 L SENSE2_RETURN LG-95/LG-95Z 1-17 1. 8. 6 PCI and PCI Express X16, X1 Slots Install PCI Express X16 graphics card into slot "PCIEX16". (For LG-95 only) Install PCI Express X1 card into slot "PCIEX1". [. . . ] Example: Memory Timing: 2. 5-3-3-7 @533MHz Graphics information: Note Graphics card's brand, model and driver version Graphics card: Type in the brand and model name of your graphics card. Example: ATI RADEON X850 XT PE Graphics driver version: Type in the driver version of your graphics card Example: Catalyst 5. 12V Power supply maker: Type in the brand and model name of your power supply unit. Power supply wattage: Type in the power wattage of your power supply unit. Storage devices: Type in the brand and specifications of your HDD drive and quantity. [. . . ]