User manual ABIT LG-95Z

[. . . ] LG-95Z LG-95C Motherboard Intel Socket 775 Installation Guide V2. 0 Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. Product names appearing in this manual are for identification purpose only and trademarks and product names or brand names appearing in this document are the property of their respective owners. [. . . ] Generally you need only one floppy disk drive in your system. The red line on the ribbon cable must be aligned with pin-1 on both the FDD port and the floppy connector. To connect SATA device: 1. Attach either end of the signal cable to the SATA connector on motherboard. Attach the other end to the SATA device. Attach the SATA power cable to the SATA device and connect the other end from the power supply. Connect the single end (blue connector) at the longer length of ribbon cable to the IDE port of this board, the other two ends (gray and black connector) at the shorter length of the ribbon cable to the connectors of your hard drives. Make sure to configure the "Master" and "Slave" relation before connecting two drives by one single ribbon cable. The red line on the ribbon cable must be aligned with pin-1 on both the IDE port and the hard-drive connector. The motherboard in this photo is served for DEMO only, and may not be the same type or model as the one described in this manual. LG-95Z V2. 0/LG-95C 9 1. 7. 3 Additional USB 2. 0 Port Headers Each header supports 2x additional USB 2. 0 ports by connecting bracket or cable to the rear I/O panel or the front-mounted USB ports of your chassis. 1. 7. 4 Internal Audio Connectors This connector connects to the audio output of internal CD-ROM drive or add-on card. Pin 1 3 5 7 Pin Assignment VCC Data0 Data0 + Ground Pin 2 4 6 8 10 Pin Assignment VCC Data1 Data1 + Ground NC Make sure the connecting cable bears the same pin assignment. 10 LG-95Z V2. 0/LG-95C 1. 7. 5 Front Panel Audio Connection Header This header provides the connection to audio connector at front panel. 1. 7. 6 PCI and PCI Express X16, X1 Slots Install PCI Express X16 graphics card into slot "PCIEX16" or "PCIEX4". Install PCI cards into slots "PCI1" and/or "PCI2". Slot PCIEX4 supports up to X4 bandwidth. Slot PCIEX16 supports up to X16 bandwidth but is available for model LG-95C only. Pin 1 2 3 4 5 6 7 8 9 10 Signal Name AUD_MIC AUD_GND AUD_MIC_BIAS AUD_VCC Filtered AUD_F_R AUD_RET_R REVD Key AUD_F_L AUD_RET_L Function Front Panel Microphone input signal Ground used by Analog Audio Circuits Microphone Power +5V used by Analog Audio Circuits Right Channel audio signal to Front Panel Right Channel Audio signal to Return from Front Panel Reserved No Pin Left Channel Audio signal to Front Panel Left Channel Audio signal to Return from Front Panel LG-95Z V2. 0/LG-95C 11 1. 8 Connecting Rear Panel I/O Devices The rear I/O part of this motherboard provides the following I/O ports: · · · · · · Mouse: Connects to PS/2 mouse. LPT1: Connects to printer or other devices that support this communication protocol. COM1: Connects to external modem, mouse or other devices that support this communication protocol. USB1/USB2: Connects to USB devices such as scanner, digital speakers, monitor, mouse, keyboard, hub, digital camera, joystick etc. (Center / Subwoofer): Connects to the center and subwoofer channel. (Rear Left / Rear Right): Connects to the rear left and rear right channel. (Surround Left / Surround Right): Connects to the surround left and surround right channel. Line-In: Connects to the line out from external audio sources. Line-Out: Connects to the front left and front right channel. Mic-In: Connects to the plug from external microphone. LG-95Z V2. 0/LG-95C · · 12 2. BIOS Setup This motherboard provides a programmable EEPROM so that you can update the BIOS utility. The BIOS (Basic Input/Output System) is a program that deals with the basic level of communication between processor and peripherals. [. . . ] Power supply wattage: Type in the power wattage of your power supply unit. Storage devices: Type in the brand and specifications of your HDD drive and quantity. Specify if it was inserted on IDE (Master or Slave) or SATA ports, including the RAID allocation status. Example 1: WD Caviar WD600 60GB (on IDE2 master), Maxtor DiamondMax 10 SATA 300GB (on SATA 3) Example 2: Maxtor DiamondMax 10 SATA 300GB *2 (on SATA 3, SATA 4 RAID 1) Optical devices: Type in the brand and specifications of your optical drives and quantity. [. . . ]