User manual ABIT UL8

[. . . ] UL8 AMD AthlonTM 64 System Board Socket 939 User's Manual 4200-0459-01 Rev. 1. 00 Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. [. . . ] Integrated Peripherals Phoenix ­ AwardBIOS CMOS Setup Utility Integrated Peripherals OnChip IDE Device Press Enter OnChip PCI Device Press Enter SuperIO Device Press Enter Onboard PCI Device Press Enter Item Help :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults # OnChip IDE Device: Click <Enter> key to enter its submenu: Phoenix ­ AwardBIOS CMOS Setup Utility OnChip IDE Device IDE Bus Master Enabled Onboard IDE-1 Controller Enabled Onboard IDE-2 Controller Enabled OnChip SATA Enabled - OnChip SATA Mode IDE Item Help :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults IDE Bus Master: This option enables or disables the IDE bus mastering capability under the DOS environment. User's Manual 3-16 Chapter 3 Onboard IDE-1 Controller/Onboard IDE-2 Controller: This item allows you to enable or disable the primary and secondary IDE controller. Select [Disabled] if you want to add a different hard drive controller. OnCip SATA: This item enables or disables the on-chip SATA controller. OnChip SATA Mode: This item determines the mode for on-chip Serial ATA. [IDE]: The on-chip Serial ATA served as IDE mode. [RAID]: The on-chip Serial ATA served as RAID mode. # OnChip PCI Device: Click <Enter> key to enter its submenu: Phoenix ­ AwardBIOS CMOS Setup Utility OnChip PCI Device OnChip USB Controller Enabled - USB 2. 0 Controller Enabled X - USB Keyboard Support Via OS X - USB Mouse Support Via OS OnChip Audio Controller Enabled Item Help :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults OnChip USB Controller: This option enables or disables the USB controller. If you choose to disable this item, the "USB Keyboard Support Via" and "USB Mouse Support Via" items will not be able to select in Integrated Peripherals menu. USB 2. 0 Controller: This option enables or disables the USB 2. 0 controller. USB Keyboard Support Via: This item allows you to select [BIOS] for using USB keyboard in DOS environment, or [OS] in OS environment. UL8 BIOS Setup !USB Mouse Support Via: 3-17 This item allows you to select [BIOS] for using USB mouse in DOS environment, or [OS] in OS environment. OnChip Audio Controller: This option enables or disables the audio controller. # Super IO Device: Click <Enter> key to enter its submenu: Phoenix ­ AwardBIOS CMOS Setup Utility SuperIO Device Onboard FDC Controller Enabled Onboard Serial Port 1 3F8/IRQ4 Onboard Parallel Port 378/IRQ7 Parallel Port Mode SPP X - EPP Mode Select EPP1. 7 X - ECP Mode Use DMA 3 Item Help :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults Onboard FDC Controller: Two options are available: Enabled and Disabled. You can enable or disable the onboard FDC controller. Onboard Serial Port 1: This is used to specify the I/O address and IRQ of Serial Port 1. Six options are available: Disabled $ 3F8/IRQ4 $ 2F8/IRQ3 $ 3E8/IRQ4 $ 2E8/IRQ3 $ AUTO. Onboard Parallel Port: Sets the I/O address and IRQ of the onboard parallel port. Four options are available: Disabled $ 378/IRQ7 $ 278/IRQ5 $ 3BC/IRQ7. Parallel Port Mode: Four options are available: SPP $ EPP $ ECP $ ECP+EPP. EPP Mode Select: Two options are available: EPP1. 7 $ EPP1. 9. The default setting is EPP 1. 7 When the mode selected for the parallel port mode is EPP, the two EPP version options are available. ECP Mode Use DMA: Chapter 3 Two options are available: 1 $ 3. When the mode selected for the parallel port mode is ECP, the DMA channel selected can be Channel 1 or Channel 3. # Onboard PCI Device: Click <Enter> key to enter its submenu: Phoenix ­ AwardBIOS CMOS Setup Utility Onboard PCI Device Onboard LAN Controller Enabled - LAN Boot ROM Disabled Item Help :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults Onboard LAN Controller: This option enables or disables the LAN controller. LAN Boot ROM: This item allows you to use the boot ROM (instead of a disk drive) to boot-up the system and access the local area network directly. UL8 BIOS Setup 3-19 3-6. [. . . ] They will be more familiar with local conditions and problems and will have better insight as to which resellers offer what products and services. Due to the huge number of emails coming in every day and other reasons, such as the time required for problem reproduction, we will not be able to reply to every email. Please understand that we are selling through distribution channels and don't have the resources to serve every end-user. However, we will try to do our best to help every customer. [. . . ]