User manual ACCUPHASE E-202

[. . . ] Cleaning ­ Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Attachments ­ Do not use attachments not recommended by the product manufacturer as they may cause hazards. Water and Moisture ­ Do not use this product near water ­ for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. [. . . ] · The ZONE3 video out is only for the ZONE3. · When a sold separately room-to-room remote control unit (ACCUPHASE RC-616, 617 or 618) is wired and connected between the MAIN ZONE and ZONE2 (ZONE3), the remote-controllable devices in the MAIN ZONE can be controlled from ZONE2 (ZONE3) using the remote control unit. Input + AC outlet (wall) AC 120 V, 60 Hz Output + AUX OUT Extension terminal for future use. RC-616 Infrared retransmitter RC-617 Infrared sensor AC OUTLETS · SWITCHED (total capacity ­ 120 W (1 A)) The power to the outlet is turned on and off in conjunction with the POWER switch on the main unit, and when the power is switched between on and standby from the remote control unit. No power is supplied from this outlet when this unit's power is at standby. Never connect equipment whose total power consumption exceeds 120 W (1 A). NOTE: · Insert the plugs securely. Incomplete connections will result in the generation of noise. · Only use the AC OUTLETS for audio equipment. Never use it for hair driers, monitors or other electrical appliances. G Monitor Monitor (ZONE2 or ZONE3) (ZONE2) VIDEO IN A L R Power amplifier Power amplifier (ZONE2 or ZONE3) (ZONE2 or ZONE3) L R L IN R · For the AUDIO output, use high quality pin-plug cables and wire in such a way that there is no humming or noise. · For instructions on installation and operation of separately sold devices, refer to the devices' operating instructions. 10 ENGLISH ENGLISH FUNCTION <PRESET ·> STATUS <SELECT> <SPEAKER> <TONE DEFEAT> VOLUME Operation Before operating Turning the sound off temporarily (MUTING) Press [MUTING]. 1 Press <POWER>. ¢ ON: The power indicator lights red. <LOUDNESS> <POWER> <CH VOL> PURE DIRECT <ON/STANDBY> <PHONES> <TONE CONTROL> £ OFF: The power turns off and the indicator is off. · Canceling MUTING mode: To cancel the muting mode, either press [MUTING] or adjust the volume. [POWER ON] FUNCTION 2 Set [MODE SELECTOR 1] to "A". 3 Set [MODE SELECTOR 2] to "CD/iPod". 4 Press <ON/STANDBY> or [POWER ON]. Playing the input source Listening over headphones Connect the headphones to <PHONES>. · No sound is produced from the speakers automatically. · The power indicator blinks green and the power turns on. (A to G) or SHIFT to select 3 Press MODE to set the manual tuning mode. Press <PRESET>, 2 the desired preset [CHANNEL] or [NUMBER] to select channel. 4 Check that the display's "AUTO" indicator turns off. The frequency changes continuously when the button is held in. · When the manual tuning mode is set, FM stereo broadcasts are received in monaural and the "STEREO" indicator turns off. · "AM" or "FM" can be selected directly by pressing [FM/AM]. About the button names in this explanation < > : Buttons on the main unit [ ] : Buttons on the remote control unit Button name only : Buttons on the main unit and remote control unit 13 ENGLISH ENGLISH Operation Operation Note: The XM Radio ID does not use the letters "I", "O", "S" or "F". Activate your XM Satellite Radio service in the U. S. online at http://activate. xmradio. com or call 1-800-XM-RADIO (1-800-9672346). XM will send a signal from the satellites to activate the full channel lineup. Activation normally takes 10 to 15 minutes, but during peak busy periods you may need to keep your XM Ready home audio system on for up to an hour. When you can access the full channel lineup on your XM Ready home audio system you are done. [. . . ] · FUNCTION knob position is not appropriate. · MUTING is on. · Connect securely. · Turn volume up to suitable level. · Switch off MUTING. 6, 7 11 11 11 7 "CHECK ANTENNA" is displayed in the XM mode. [. . . ]