User manual ACER AAG530

[. . . ] Acer Altos G530 Series User's Guide Copyright © 2005 Acer Incorporated All Rights Reserved. Acer Altos G530 Series User's Guide Changes may be made periodically to the information in this publication without obligation to notify any person of such revision or changes. Such changes will be incorporated in new editions of this manual or supplementary documents and publications. This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims the implied warranties of merchantability or fitness for a particular purpose. [. . . ] Select a graphic controller as a primary boot device. Note: This parameter will be grayed out when the Onboard Video is set to Disabled. Enables or disables the onboard NIC1 (Gigabit network interface controller). Enables or disables the onboard NIC1 ROM. Option Enabled Disabled Disabled Enabled Onboard NIC1 (Left) Onboard NIC1 ROM Enabled Disabled Enabled Disabled 100 4 BIOS setup Parameter Onboard NIC 2 (Right) Description Enables or disables the onboard NIC2 (10Base-T/ 100Base/ 1000 Base network interface controller). Enables or disables the onboard NIC2 ROM. Option Enabled Disabled Onboard NIC2 ROM Onboard SCSI Enabled Disabled Enabled Disabled Enabled Disabled Enables or disables the onboard SCSI ontroller. Enables or disables the onboard SCSI ROM. Onboard SCSI ROM Onboard SCSI Mode Select a SCSI mode. Different RAID options, such as RAID 0, RAID 1 or expanded RAID arrays, are offered in the integrated SCSI controller. Enables or disables the PCI 32/33 slot. IM/IME (RAID1/ 1e) IS (RAID 0) Slot 5 Option ROM Enabled Disabled 101 Memory Configuration The Memory Configuration submenu provides information about the DIMMs installed in DIMM slots 1A, 1B, 2A, and 2B. Parameter DIMM 1A, 1B, 2A and 2B Description Indicates the current memory status. Option Installed Not Installed Disabled Spare Extended Memory Test Settings for extended memory test. Disabled 1 MB 1 KB Every Location 102 4 BIOS setup Parameter Memory Retest Description When Enabled, BIOS will activate and retest all DIMMs on next boot. Note: This parameter will automatically reset to Disabled. Enables or disables remapping of overlapped PCI memory above the physical memory. When set to Spare, a DIMM slot is kept in reserve for standby in the event a significant failure occurs in the primary DIMM. If a threshold of runtime error occurs in the primary DIMM, that DIMM will have its data copied to the spare DIMM. Option Disabled Enabled Memory Remap Feature Memory Sparing Enabled Disabled Disabled Spare 103 Boot The Boot menu allows you to set the drive priority during system bootup. It also displays information about the installed storage devices. Press Enter to enter the submenu screen of the parameters shown in the screen below. 104 4 BIOS setup Boot Settings Configuration The Boot Settings Configuration submenu lets you specify the preferred settings for system bootup. Parameter Quick Boot Description Allows the system to boot faster by skipping some POST routine. Enables or disables the Quiet Boot function. When set to Enabled, BIOS setup is in graphical mode and displays only an identification logo during POST and while booting. After booting the screen displays the operating system prompt (such as DOS) or logo (such as Windows). If any error occurs while booting, the system automatically switched to text mode. Option Enabled Disabled Disabled Enabled Quiet Boot 105 Parameter Bootup Num-Lock PS/2 Mouse Support Description Activates the Numeric Lock function upon booting. Enable this parameter if you intend to use a mouse or trackball with a PS/2 interface. Option Off On Auto Enabled Disabled Enabled Disabled POST Error Pause When this parameter is Enabled, you will be prompted when an error is detected during boot up. When set to Disabled, the system will boot with no intervention, if possible. When this parameter is Enabled, you will be prompted to press F2 to run BIOS during boot up. Allows BIOS to scan Flash ROM for user binaries. Hit `F2' Message Display Scan User Flash Area Enabled Disabled Disabled Enabled 106 4 BIOS setup Boot Device Priority The Boot Device Priority submenu lets you specify the boot search sequence during the POST process. [. . . ] After a few seconds, the Management menu appears. Loading the RAID card default setting 1 2 3 In the Management menu, select Objects, then select Adapter. Select Factory Default, then Yes to load the default settings. Press Ctrl+Alt+Del to reboot the server. 177 Creating a RAID 1 volume 1 2 3 4 After rebooting the server, press Ctrl+M to enter the MegaRAID Configuration screen. Select New Configuration, then select YES. [. . . ]