User manual ACER AL1521

[. . . ] TABLE OF CONTENTS FOR YOUR SAFETY ------------------------------------------------SAFETY PRECAUTIONS -----------------------------------SPECIAL NOTES ON LCD MONITORS -----------------BEFORE YOU OPERATE THE MONITOR -------------------FEATURES ------------------------------------------------------PACKING LIST -------------------------------------------------INSTALLATION INSTRUCTIONS -------------------------CONTROLS AND CONNECTORS ------------------------ADJUSTING THE VIEWING ANGLE ---------------------OPERATING INSTRUCTIONS -----------------------------------GENERAL INSTRUCTIONS --------------------------------HOW TO ADJUST A SETTING ----------------------------ADJUSTING THE PICTURE --------------------------------PLUG AND PLAY ----------------------------------------------TECHNICAL SUPPORT(FAQ) ------------------------------------ERROR MESSAGE & POSSIBLE SOLUTION --------APPENDIX -------------------------------------------------------------SPECIFICATIONS ---------------------------------------------FACTORY PRESET TIMING TABLE ---------------------CONNECTOR PIN ASSIGNMENT ------------------------- 1 2 3 3 3 3 4 5 6 7 7 9 10-11 12 13-14 15 16 16-17 18 19 41L1500-786-1A Before operating the monitor please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] The AC-power cord may be connected to either a wall power outlet or the power outlet socket on your PC, depending on the type of power cord supplied with your LCD monitor. NOTES A certified power supply cord has to be used with this equipment. The relevant national installation and/or equipment regulations shall be considered. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 0. 75mm2 or 2 H05VVH2-F2 3G 0. 75mm ) shall be used. Alternatively a flexible cord of 2 synthetic rubber according to IEC 60245 (designation H05RR-F 3G 0. 75mm ) may be used. 41L1500-786-1A 4 CONTROLS AND CONNECTORS CABLE CONNECTIONS Turn off your computer before performing the procedure below. Connect the power adapter dc cable to the DC-In port on the back of the monitor. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port. (Only Dual-Input Model) Connect one end of the 24-pin DVI cable to the back of the monitor and connect the other end to the computer's DVI port. Connect the audio cable between the monitor's audio input and the PC's audio output (green port). Plug the power cable of your monitor into a nearby outlet. Plug the other end of the power cord into the power adapter. Caution: If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied). Figure 1 1. D-SUB Cable DVI Cable Audio Cable Connecting Cables 4. External Adapter AC Power Cord 41L1500-786-1A 5 ADJUSTING THE VIEWING ANGLE · For optimal viewing it is recommended to look at the full face of the monitor, then to adjust the monitor's angle to your own preference. · Hold the stand so you do not topple the monitor when you change the monitor's angle. · You may adjust the monitor's angle from -5° to 20°. Figure 2 NOTES · Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. · Careful attention is required not to catch your fingers or hands when you change the angle. 41L1500-786-1A 6 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power switch to turn the monitor on or off. The other control knobs are located at front panel of the monitor (See Figure 3). By changing these settings, the picture can be adjusted to your personal preferences. · The power cord should be connected. · Connect the video cable from the monitor to the video card. · Press the power switch to turn on the monitor. The power indicator LED will light up. Figure 3 EXTERNAL CONTROLS 1. </ Volume 3. External Controls 4. 5. /MENU/ENTER /Auto Adjust Key/Exit /Power Key 41L1500-786-1A 7 FRONT PANEL CONTROL · · /Power Key: Press this knob to switch ON/OFF of monitor's power. /MENU/ENTER : Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD menu when in Volume Adjust OSD status. Activates the volume control when the OSD is OFF or navigate through adjustment icons when OSD is ON or adjust a function when function is activated. · </Volume: · >/Volume: Activates the volume control when the OSD is OFF or navigate through adjustment icons when OSD is ON or adjust a function when function is activated. · 1. [. . . ] *Adjust the Contrast and Brightness Controls. *Move electrical devices that may cause electrical interference. *The Computer Power Switch should be in the ON position. *The Computer Video Card should be snugly seated in its slot. [. . . ]