User manual ACER AL1531

[. . . ] 4 Chapter 2 Display Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 User Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Adjusting the Monitor's Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Function Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Chapter 3 Technical Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] After you unpack the LCD Monitor, make sure that the following items were included in the box: * LCD Monitor * User's Manual * 1. 8M Monitor-to-PC VGA Cable * AC Adapter * 1. 8M Monitor-to-PC DVI-D Cable * 1. 8M Power Cord * 1. 8M Stereo Jack Audio Cable If you find that any of these items is missing or appears damaged, contact your dealer immediately. Connecting the LCD Monitor and Base When you open the box to take the base and put on the desk first. Then connect the LCD Monitor and base and screw it locked please. (See fig. 1-1 ) Figure 1-1 Viewing Angle Adjustment The LCD Monitor is designed to allow users to have a comfortable viewing angle. The viewing angle can be adjusted from -5°to +20°. (See fig. 1-2). Figure 1-2 Warning: Do not force the LCD Monitor over its maximum viewing angle settings as stated above. Attempting this will result in damaging the Monitor and Monitor stand. 2 Detaching LCD Monitor from Its Stand Unscrew screws body. the swivel base support column and pull it from main Figure 1-3 Interface for Arm Applications Before installing to mounting device, please refer to Fig. 1-3. The rear of this LCD display has four integrated 4 mm, 0. 7 pitches threaded nuts, as well as four 5 mm access holes in the plastic covering as illustrated in Figure 1-4. These specifications meet the VESA Flat Panel Monitor Physical Mounting Interface Standard (paragraphs 2. 1 and 2. 1. 3, version 1, dated 13 November 1997). Note :Please using Ø 4mm x 8mm (L) screw for this application Figure 1-4 Connecting the Display to your Computer 1. Connect one end of the signal cable to the LCD Monitor's VGA port or DVI port. (See Fig 1-5) 3. Connect the other end of the signal cable to the VGA port or DVI port on your PC. Attention: This device must be connected to an off-the-shelf video cable in order to comply with FCC regulations. A ferrite-core interface cable is included in the LCD Monitor package. This device will not be in compliance with FCC regulations when a non-ferrite-core video cable is used. Connecting the AC Power 1. Connect the power cord to the AC adapter. (See Fig. Connect the AC adapter's DC output connector to the DC Power Jack of the monitor. Connect the power cord to an AC power source. Figure 1-6 Warning:We recommand to install a "Surge Protector" device between the AC Adapter and the electrical wall outlet for adding protection against power surges to prevent the errects of sudden voltage variations from reaching the LCD Monitor. Sudden power surges may damage your monitor. Connecting the Audio Cable 1. Connect the audio cable to the " LINE OUT " jack on your PC's audio card or to the front panel's "AUDIO OUT" jack of your CD ROM drive. Connect the other end of the audio cable to the LCD Monitor's " LINE IN " jack. Figure 1-7 3 Setting Up the LCD Monitor 1. Make sure the AC power cord is connected to the LCD Monitor. 2. Turn on the LCD Monitor's power switch, located on the bezel of the monitor. Power Management System This LCD Monitor complies with the VESA DPMS (version 1. 0) Power Management guidelines. [. . . ] Make sure the power indicator on the LCD Monitor is ON, all connections are secured, and the system is running on the correct timing. Refer to Chapter 3 for information on timing. Turn off the LCD Monitor and then turn it back on again. If there is still no picture, press the Adjustment Control button several times. [. . . ]