User manual ACER AL1913

[. . . ] 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Keep the display away from your eyes at least by 30 cm. The upper edge of the display should be a little higher than your sight. Adjust the front and back dip angles of the display based on your visual angle so that you can view the display comfortably. Quick Installation Complete the following steps for quick installation: (See the figure) Assemble the seat of the display Take the seat out of the box and place it on a flat table. Take your LCD display out of the carton and assemble the display and seat along the rail. You will hear a click sound when the display and seat are engaged correctly. 2 Connection to PC Make sure that the power supply of your PC is turned off and the power plug is removed. Connect and fasten both ends of the signal cable to your PC host and LCD display respectively. If your LCD display has built-in speakers, connect the audio cable attached to the display from the sound card output of your PC to the audio input on the back of your LCD display. Connect the attached power cable to your LCD display. Turn on the power supplies of your PC and LCD display. Transformer DC end Audio Cable Signal Cable Adjustment of Display Key Definition Power Source 1 2 3 4 5 MENU > < AUTO OSD Manu Plus Minus Automatic Adjustment Power On/Off Green indication: Power is on and normal Orange indication: Sleep status in the energy-saving mode Colorless indication: Power off Press this button to enter OSD. Press this button for selection or adjustment when OSD is shown. Press this button and click < and > to adjust volume when OSD is not shown (for the model with speakers only) Press this button to exit the manual when OSD is shown. Press this button for the display to optimize the position, phase and clock pulse automatically when OSD is not shown. 6 Speaker (For the model with speakers) 3 Operation Your LCD display has been adjusted to its optimal status before shipment. Your can also adjust the image in accordance with the following illustrations and steps. Click MENU to display the OSD window as shown in the following figure. Click < or > to select the function to be adjusted as shown in the following figure. Click the MENU button to select the function to be adjusted. [. . . ] Set up the reference position. 6 Technical Specifications Panel Dimension Max. Pixel Pixel Span LCD Panel Brightness (Back Light Source) Contrast LC Response Time Visual Angle Effective Display Signal Mode Input Signal SYNC Frequency Max. Pixel Clock Input Terminal Image Audio Diagonal 481. 4mm (19 inch) LCD display 1, 440 x 900/WXGA+ Up to 16. 2M true color Horizontal 0. 284mm x Vertical 0. 284mm 350 cd/m2 500 : 1 20 ms Horizontal 170° / Vertical 170° Horizontal 408. 24mm x Vertical 255. 15mm Simulated video frequency: 0. 7 Vpp, 75 (separate SYNC and composite SYNC) Horizontal 30kHz~82kHz x Vertical 56Hz ~76 Hz 135MHz D-Sub 15 PIN (VESA) Phone Jack, d=3. 5mm (Optional) AC100~240Volts, 50/60Hz 60W / Standby 3W 5 ~ 35 (operation)/ -20 ~ 55 (storage) 20% ~ 80% (operation)/ 20% ~ 85% (storage) 462 mm x 180mm x 385mm 4. 0 kg TCO99;UL/CUL;TÜV-GS;CE/LVD;TÜV-ERGO;CB;CCC;FCC-B; VCCI-B;CE/EMC;C-Tick; BSMI; ISO 13406-2;EPA; PCT;NOM Power Transformer Power Consumption Environmental Conditions Temperature Humidity Actual Dimension (W x D x H) Net Weight Safety Standard Lamp Disposal LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. [. . . ]