User manual ACER AL712

[. . . ] 3 Chapter 2 Display Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 User Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Adjusting the Monitor's Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Function Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Chapter 3 Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Make sure that LCD Monitor has enough space around it for sufficient airflow. Though the LCD Monitor uses very little power, some ventilation is needed to ensure that the Monitor does not become too hot. AL711 AL712 AL713 AL715 AL716 AL717 X O O X X X DVI-D X O X X O X AUDIO After you unpack the LCD Monitor, make sure that the following items were included in the box: * LCD Monitor * 1. 8M Monitor-to-PC VGA Cable * 1. 8M Monitor-to-PC DVI-D Cable * User's Manual * 1. 5M Stereo Jack Audio Cable * 1. 8M Power Cord * Base If you find that any of these items is missing or appears damaged, contact your dealer immediately. Connecting the LCD Monitor and Base When you open the box to take the base and put on the desk first. Then connect the LCD Monitor and base please. (See fig. 1-1 ) Figure 1-1 Viewing Angle Adjustment The LCD Monitor is designed to allow users to have a comfortable viewing angle. The viewing angle can be adjusted from -5°to +30°. (See fig. 1-2) Figure 1-2 Warning Do not force the LCD Monitor over its maximum viewing angle settings as stated above. Attempting this will result in damaging the Monitor and Monitor stand. 2 Detaching LCD Monitor from Its Stand Unscrew screws the swivel base support column and pull down the hinge to release. Figure 1-3 Interface for Arm Applications Before installing to mounting device, please refer to Fig. 1-3. The rear of this LCD display has four integrated 4 mm, 0. 7 pitches threaded nuts, as well as four 5 mm access holes in the plastic covering as illustrated in Figure 1-4. These specifications meet the VESA Flat Panel Monitor Physical Mounting Interface Standard (paragraphs 2. 1 and 2. 1. 3, version 1, dated 13 November 1997). Figure 1-4 Connecting the Display 1. Connect one end of the signal cable to the LCD Monitor's VGA port or DVI port. (For AL712/AL713)(See Fig 1-5) 3. Connect the other end of the signal cable to the VGA port or DVI port on your PC. 4. Make sure connection are secure. A ferrite-core interface cable is included in the LCD Monitor package. This device will not be in compliance with FCC regulations when a non-ferrite-core video cable is used. Figure 1-5 Attention: This device must be connected to an off-the-shelf video cable in order to comply with FCC regulations. Connecting the AC Power 1. Connect the power cord to the LCD Monitor. (See Fig. Connect the power cord to an AC power source. Figure 1-6 Connecting the Audio Cable (For AL712/AL716) 1. Connect the audio cable to the " LINE OUT " jack on your PC's audio card or to the front panel's "AUDIO OUT" jack of your CD ROM drive. Connect the other end of the audio cable to the LCD Monitor's " LINE IN " jack. Figure 1-7 Setting Up the LCD Monitor 1. Turn on the LCD monitor's hard power switch, located on the back of the monitor 2. Turn on the LCD Monitor's soft power switch, located on the bezel of the monitor. Figure 1-8 Power Management System This LCD Monitor complies with the VESA DPMS (version 1. 0) Power Management guidelines. The VESA DPMS provides four power saving modes through detecting a horizontal or vertical sync. When the LCD Monitor is in power saving mode, the monitor screen will be blank and the power LED indicator will light yellow. 3 Chapter 2 Display Controls User Controls A brief description and the location of all LCD Monitor function controls and indicators: Figure 2-1 1 2 3 4 5 6 7 Stereo Speakers (AL712/AL716) Speaker Volume Control (AL712/AL716) Soft Power Switch DC Power-On Indicator Function Select Buttons Adjustment Control Buttons External Headphone Jack (AL712/AL716) PC Audio Stereo output. [. . . ] Make sure the power indicator on the LCD Monitor is ON, all connections are secured, and the system is running on the correct timing. Refer to Chapter 3 for information on timing. Turn off the LCD Monitor and then turn it back on again. If there is still no picture, press the Adjustment Control button several times. [. . . ]