User manual ACER AT150 F1

[. . . ] 6 Screen position adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Connecting the power cord. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Safety precaution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Cleaning your monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Eyes · Rest your eyes frequently. · Give your eyes regular breaks by looking away from the monitor and focusing on a distant point. · Blink frequently to keep your eyes from drying out. Display · Keep your display clean. · Keep your head at a higher level than the top edge of the display so your eyes point downward when looking at the middle of the display. · Adjust the display brightness and/or contrast to a comfortable level for enhanced text readability and graphics clarity. · Eliminate glare and reflections by: · placing your display in such a way that the side faces the window or any light source · minimizing room light by using drapes, shades or blinds · using a task light · changing the display's viewing angle · using a glare-reduction filter · using a display visor, such as a piece of cardboard extended from the display's top front edge · Avoid adjusting your display to an awkward viewing angle. · Avoid looking at bright light sources, such as open windows, for extended periods of time. Developing good work habits Develop the following work habits to make your computer use more relaxing and productive: · Take short breaks regularly and often. · Perform some stretching exercises. · Breathe fresh air as often as possible. · Exercise regularly and maintain a healthy body. The DDC (Display Data Channel) is a communication protocol through which the monitor automatically informs the host system about its capabilities, for example, supported resolutions and corresponding timing. The monitor supports DDC2B standard. EN-8 AT150 F1W CONNECTOR PIN ASSIGNMENT 15-Pin Color Display Signal Cable PIN NO. DESCRIPTION Red Green Blue Monitor Ground DDC-return R-Ground G-Ground B-Ground PIN NO. DESCRIPTION +5V Logic Ground Monitor Ground DDC-Serial Data H-Sync V-Sync DDC-Serial Clock EN-9 AT150 F1W 24-Pin Color Display Signal Cable PIN 1. Meaning TMDS Data2TMDS Data2+ TMDS Data 2/4 Shield TMDS Data4TMDS Data4+ DDC Clock DDC Data Analogue Vertical Sync TMDS Data1TMDS Data1+ TMDS Data 1/3 Shield TMDS Data3EN-10 PIN 13. Meaning TMDS Data3+ +5V Power GND(return for +5V hsync. vsync) Hot Plug Detect TMDS Data0TMDS Data0+ TMDS Data 0/5 Shield TMDS Data5TMDS Data5+ TMDS Clock Shield TMDS Clock+ DDC TMDS Clock- AT150 F1W Standard Timing Table To reduce the need for adjustment for different modes, the monitor has default setting modes that are most commonly used as given in the table below. For optimum adjustment, the user is suggested to perform the Auto Setup under Windows "Full Screen" pattern or using the pattern in the floppy disk provided. When none of the mode is matched, the user can store their preferred modes in the user modes. The monitor is capable of storing up to 9 user modes. 5. < / > Press < or > to select the desired function. Press < or > to change the settings of the current function. 6. MENU / ENTER: Activate OSD menu when OSD is OFF or activate/de-activate adjustment function whenOSD is ON or Exit OSD menu when in Volume Adjust OSD status. [. . . ] Select input signal from analog (D-Sub) Select input signal from digital(DVI) (only Dual-Input Model) Turn ON/OFF DDC/CI support Show the resolution, H/V frequency andinput port of current input timing. Clear each old status of Autoconfigurationand set the color temperature to Cool. Save user adjustment and OSD disappear. N/A N/A N/A N/A N/A Exit EN-19 AT150 F1W TROUBLESHOOTING Before sending your LCD monitor for servicing, please check the troubleshooting list below to see if you can self-diagnose the problem. (VGA Mode) Problems Current Status Remedy LED ON · Using OSD, adjust brightness and contrast to maximum or reset to their default settings. [. . . ]