User manual ACER B223WL

[. . . ] This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. [. . . ] Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image, when the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image or turning off the Power Switch for hours. BEFORE YOU OPERATE THE MONITOR FEATURES · · · · · · · 43. 2cm(17") TFT Color LCD Monitor Crisp, Clear Display for Windows Recommened Resolutions: 1280 X 1024 @60Hz EPA ENERGY STAR® Dual Input (DVI + Analog) (Only Dual-Input Model) Ergonomic Design (TCO'03 Approved) Space Saving, Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items: 1. LCD Monitor Owner's Manual Power Cord External Adapter 15-pin D-Sub Cable DVI Cable(Only Dual-Input Model) Audio Cable Pivot Software (Only B223WL r) 3 INSTALLATION INSTRUCTIONS (Only B223WL h/B223WL r) Support Frame Do not perform a pulling or plugging action when the display is under slanting status to prevent the display from ejecting. Pull out the pin from the display support frame as per the figure and then adjust the height. Note that upon pulling out the pin, erect the machine on the table to prevent the top part of the display from ejecting. Make sure that the power cord is the correct type required in your area. This LCD monitor has an External universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required. ) 3. Connect the AC-power cord into your LCD monitor's DC-power-input. The AC-power cord may be connected to either a wall power outlet or the power outlet socket on your PC, depending on the type of power cord supplied with your LCD monitor. NOTES A certified power supply cord has to be used with this equipment. The relevant national installation and/or equipment regulations shall be considered. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 0. 75mm2 or H05VVH2-F2 3G 0. 75mm2) shall be used. · The power cord should be connected. · Connect the video cable from the monitor to the video card. · Press the power button to turn on the monitor position. The power indicator will light up. Figure 3 EXTERNAL CONTROLS 1. </ Volume 3. External Control Button 4. 5. /MENU/ENTER /Auto Adjust Key/Exit /Power Key 7 FRONT PANEL CONTROL · /Power Button: Press this button to turn the monitor ON or OFF, And display the monitor's state. Blue -- Orange -- Light blue -- Power On mode. Off mode. · Power Indicator: · /MENU / ENTER : Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD menu when in Volume Adjust OSD status. Activates the volume control when the OSD is OFF or navigate through adjustment icons when OSD is ON or adjust a function when function is activated. · </Volume: · >/Volume: Activates the volume control when the OSD is OFF or navigate through adjustment icons when OSD is ON or adjust a function when function is activated. · 1. 2. /Auto Adjust button / Exit: When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu). When OSD menu is in off status, press this button for 2 seconds to activate the Auto Adjustment function. The Auto Adjustment function is used to set the HPos, VPos, Clock and Focus. NOTES · Do not install the monitor in a location near heat sources such as radiators · · · or air ducts, or in a place subject to direct sunlight, or excessive dust or mechanical vibration or shock. Save the original shipping carton and packing materials, as they will come in handy if you ever have to ship your monitor. [. . . ] Supplied with units intended for connection to power outlet of personal computer: Please use a cord set consisting of a minimum No. 18 AWG, type SJT or SVT three conductors flexible cord. One end terminates with a grounding type attachment plug, rated 10A, 250V, CEE-22 male configuration. The other end terminates with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration. [. . . ]