User manual ACER B233HL

[. . . ] 3 Chapter 1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Connecting the LCD Monitor and Base. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Viewing Angle Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Do not apply pressure to the LCD screen. Excess pressure may cause permanent damage to the display. Do not remove the cover or attempt to service this unit by yourself. Servicing of any nature should be performed by an authorized technician. Store LCD Monitor in a room with a room temperature of -20° ~ 60°C (or -4° ~ 140°F). Storing the LCD Monitor outside this range could result in permanent damage. If any of the following occurs, immediately unplug your monitor and call an authorized technician. * Monitor to PC signal cable is frayed or damaged. * Liquid spilled into LCD Monitor or the monitor has been exposed to rain. Only use the supplied main lead to connect the monitor. For a nominal current up to 6A and a device weight above 3 kg, a line not lighter than H05VV-F, 3G, 0. 75 mm2 must be used. 3 Chapter 1 Installation Unpacking Before unpacking the LCD Monitor, prepare a suitable workspace for your Monitor and computer. Connect the video cable from the monitor to the video card. Press the power button to turn on the monitor position. The power indicator will light up. Figure 2-1 External Controls 1 2 3 Auto Adjust Key/Exit </ Volume >/ Volume 4 5 6 MENU/ENTER LED / Power Key 7 Front Panel Control /Power Button: Press this button to turn the monitor ON or OFF, And display the monitor's state. Power Indicator: Green -- Power On mode. Orange -- off mode MENU / ENTER : Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD menu when in Volume Adjust OSD status. </Volume: Activates the volume control when the OSD is OFF (only for Audio model) or navigate through adjustment icons when OSD is ON or adjust a function when function is activated. >/Volume: Activates the volume control when the OSD is OFF (only for Audio model) or navigate through adjustment icons when OSD is ON or adjust a function when function is activated. Auto Adjust button / Exit: 1. When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu). When OSD menu is in off status, press this button for 2 seconds to activate the Auto Adjustment function. The Auto Adjustment function is used to set the HPos, VPos, Clock and Focus. NOTES · E Do not install the monitor in a location near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, or excessive dust or mechanical vibration or shock. · E Save the original shipping carton and packing materials, as they will come in handy if you ever have to ship your monitor. · E For maximum protection, repackage your monitor as it was originally packed at the factory. · E To keep the monitor looking new, periodically clean it with a soft cloth. [. . . ] Position OSD Timeout Multi-language selection. Adjust the horizontal position of the OSD. Adjust the vertical position of the OSD. Auto Adjust the H/V Position, Focus and Clock of picture. Show the resolution, H/V frequency and input port of current iput timing. [. . . ]