User manual ACER H6510BD

[. . . ] Record the model number, serial number, purchase date, and place of purchase information in the space provided below. The serial number and model number are recorded on the label affixed to your computer. All correspondence concerning your unit should include the serial number, model number, and purchase information. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopy, recording, or otherwise, without the prior written permission of Acer Incorporated. Model Number : _________________________________ Serial Number: ___________________________________ Purchase Date: ___________________________________ Place of Purchase: ________________________________ Acer and the Acer logo are registered trademarks of Acer Inc. [. . . ] Indicates the hard disk type device. Processor Type Processor Speed CPU ID Level 1 Cache Level 2 Cache Primary/Secondary/ Third/Fourth IDE Master Primary/Secondary IDE Slave Total Memory Indicates the type of IDE device. Indicates the total amount of onboard memory. The memory size is automatically detected by BIOS during the POST. If you install additional memory, the system automatically adjusts this parameter to display the new memory size. Press Enter to access the Total Memory submenu. DDR Memory Type Type of memory module currently installed in the server. Indicates the type of bank interleave currently supported by the memory. Indicates the type of mouse connected to the server. Interleave support Mouse (PS2, USB) 88 4 BIOS setup Parameter Keyboard (PS2, USB) Description Indicates the type of keyboad connected to the server. Total Memory The screen below appears when you select Total Memory from the System Information window. The Total Memory menu displays the type and size of DRAM installed in DIMM slots 1A, 1B, 2A, 2B, 3A, 3B, 4A, and 4B. The Not Installed setting indicates that there is no DDR2 DRAM installed. 89 Product Information The screen below appears when you select Product Information from the Main window. The Product Information menu displays general data about the system, such as the product name, BIOS version, mainboard ID, serial number, etc. These entries are for reference only and are not user-configurable. Parameter System Product Name System Serial No Baseboard ID Baseboard Serial No Description System's model name. System's serial number. System board's identification number. If you set this parameter to Auto, BIOS setup automatically detects if the installed hard disk drive supports the Block Mode function. If supported, it allows data transfer in blocks (multiple sectors) at a rate of 256 bytes per cycle. If you set this parameter to Disabled, data transfer from and to the device occurs one sector at a time. Option Auto Disabled Block Mode Auto Disabled PIO Mode When set to Auto, BIOS setup automatically detects if the installed hard disk supports the function. If supported, it allows for faster data recovery and read/write timing that reduces hard disk activity time. This results in better hard disk performance. Mode 0 to 4 provide progressive increase of performance. Selects DMA mode. Auto 0 1 2 3 4 DMA Mode Auto SWDMAn MWDMAn UDMAn S. M. A. R. T Enables or disables the SMART (Self-Monitoring, Analysis and Reporting Technology) function of the internal hard disk. If 'Auto' is selected, BIOS setup will enable the S. M. A. R. T function if the drive supports it. Auto Disabled Enabled 32-bit Data Transfer Enables or disables the 32-bit data transfer function Disabled Enabled 97 Floppy Configuration The Floppy Configuration submenu displays the type of floppy drive installed in the server. Parameter Floppy A Description Floppy disk drive type Option 1. 44 MB, 3. 5-inch Disabled 98 4 BIOS setup PCI/PnP Configuration The PCI/PnP Configuration submenu lets you specify the settings for the PCI devices. Parameter Reset Resource Assignment Description BIOS setup stores the configuration data of Plug and Play devices in NVRAM (Non-volatile Random Access Memory). When this parameter is set to Yes, current data is deleted and a new set of information is created during the next system bootup. Option No Yes USB Function Enables or disables the USB ports. Enabled Disabled Legacy USB Support Enable this parameter when you intend to use a USB device in a non-Plug and Play operating system, such as DOS. Auto 99 Boot Settings Configuration The Boot Settings Configuration submenu lets you specify the preferred settings for system bootup. Parameter Quick Boot Description Allows the system to boot faster by skipping some POST routine. Option Enabled Disabled 100 4 BIOS setup Parameter Quiet Boot Description Enables or disables the Quiet Boot function. When set to Enabled, BIOS setup is in graphical mode and displays only an identification logo during POST and while booting. After booting, the screen displays the operating system prompt (such as DOS) or logo (such as Windows 95). [. . . ] The InstallShield Wizard Complete window appears. (14) Select the Yes, I want to restart my computer now radio button. (15) Click Finish. 176 Appendix D: ePanel ePanel module The module boasts of a true-color high resolution LCD screen. A configuration program is built into the ePanel board allowing you: · · Configure the network settings View general data about the server such as: · · · · System information, System health (i. e. , temperature, voltage, fan speed, etc. ) System resource utilization (i. e. , CPU, memory, HDD, etc. ) Power off and restart the server. Use the module keys to move around the ePanel utility. No. 1 Icon Key LCD display Function Displays your system's basic configuration information. [. . . ]