User manual ACER P1206

[. . . ] 4 Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Package Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Main Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press the "Power/ Standby" button again to confirm, otherwise the message will disappear after 5 seconds. The cooling fans continue to operate for about 60 seconds for cooling cycle and the Power LED will keep green. When the Power LED begins flashing, the projector has entered standby mode. If you wish to turn the projector back on, you must wait until the projector has completed the cooling cycle and has entered standby mode. Once in standby mode, simply press "Power/Standby" button to restart the projector. Disconnect the power cord from the electrical outlet and the projector. Do not turn on the projector immediately following a power off procedure. Warning Indicator When the "LAMP" indicator lights solid red, the projector will automatically shut itself down. Please contact your local reseller or service center. When the "TEMP" indicator lights solid red for about 20 seconds, it indicates the projector has been overheated. You will see a message "Projector Overheated. Lamp will automatically turn off soon. " on the on-screen display. The OSD menu will close and the projector will automatically save the new settings. Main Menu Sub Menu Settings 17 . . . English User Controls Personals (Computer / Video Mode) Edits user preferences by OSD interface. Edited user Info will display on lower left corner of the screen when projector is powered ON. 1. > Use the to select "Line1" function, and then press the "Enter" button. You can input the character to line one. to select character, and then press 2. > Use the "Enter" to confirm your selection. 3. > Use the to select "Line2" function, and then press the "Enter" button. You can input the character to line two. 3. > 5. > Use the to select "Save & Exit" function and then press the "Enter" button. 6. > The startup screen will display the new wording after restart the projector. Note: 4 Each line can input 35 characters only. 4 Use "Del" to delete the previous character. [. . . ] 4 If you can't select 4:3 aspect ratio type on your DVD player, please select 4:3 aspect ratio in the on screen menu. Problem: Image is reversed. 4 Select "Management" from the OSD and adjust the projection direction. See page 25. Problem: Lamp burns out or makes a popping sound 4 When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp". [. . . ]