User manual ACER S211HL

[. . . ] 3 Interface for Arm Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Connecting the Display to your Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Connecting the AC Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Connecting the Audio Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] After you unpack the LCD Monitor, make sure that the following items were included in the box: * LCD Monitor * User's Manual * 1. 8M Monitor-to-PC VGA Cable * AC Adapter * 1. 8M Monitor-to-PC DVI-D Cable * 1. 8M Power Cord * 1. 8M Stereo Jack Audio Cable * 1. 8M S-Video Cable * 1. 8M RCA Jack Audio Video Cable If you find that any of these items is missing or appears damaged, contact your dealer immediately. Connecting the LCD Monitor and Base When you open the box to take the base and put on the desk first. Then connect the LCD Monitor and base and screw it locked please. (See fig. 1-1 ) Figure 1-1 Viewing Angle Adjustment The LCD Monitor is designed to allow users to have a comfortable viewing angle. The viewing angle can be adjusted from -5°to +25°. (See fig. 1-2). -5 +25 Figure 1-2 Warning: Do not force the LCD Monitor over its maximum viewing angle settings as stated above. Attempting this will result in damaging the Monitor and Monitor stand. 2 Detaching LCD Monitor from Its Stand Unscrew screws the swivel base support column and pull it from main body. 1 Figure 1-3 Interface for Arm Applications Before installing to mounting device, please refer to Fig. 1-3. The rear of this LCD display has four integrated 4 mm, 0. 7 pitches threaded nuts, as well as four 5 mm access holes in the plastic covering as illustrated in Figure 1-4. These specifications meet the VESA Flat Panel Monitor Physical Mounting Interface Standard (paragraphs 2. 1 and 2. 1. 3, version 1, dated 13 November 1997). Note :Please using Ø 4mm x 8mm (L) screw for this application Figure 1-4 Connecting the Display to your Computer 1. Connect one end of the signal cable to the LCD Monitor's VGA port or DVI port. (See Fig 1-5) 3. Connect the other end of the signal cable to the VGA port or DVI port on your PC. You can Press the left button to decrease the OSD setting and press the right button to increase the OSD setting. Press the Menu will show OSD (On Screen Display) Function Menus table. When OSD (On Screen Display) Menus display press Menu Buttons will enable selection function. 4 Adjusting the Monitor's Display OSD Function Menu The monitor has four function control buttons to select among functions shown on OSD menu, designed for easy user-viewing environments. To access OSD Main menu, simply press one of the Function Select control buttons, and the menu diagram will pop up on the screen as shown on Fig. 2-2: Continue pressing the Function Select buttons to scroll through the entire menu items , then press Adjustment Control buttons to adjust content of selected item. Figure 2-2 Function Description Analog RGB / Digital RGB Picture Auto adjust Brightness Contrast H-position V-position Phase Clock Exit Press > button, auto adjust the display mode to its utmost performance according to VGA setting. Adjust the overall image and background screen brightness. Adjust the image brightness in relation to the background. To move the picture image horizontally left or right. To move the picture image vertically up or down. To improve focus clarity an image stability. To increase or decrease the horizontal size of image. [. . . ] You can select opaque or translucent to change OSD background. You can select on or off to display OSD icon. Reset the currently highlight control to the factory setting. User must be using factory preset video mode to use this function. [. . . ]