User manual ACER S5201B QUICK START GUIDE

[. . . ] 4 Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Package Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Main Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When the "TEMP" indicator solid red for about 10 seconds, Please contact your local dealer or our service center. English. . . 12 Installation Adjusting the Projected Image Adjusting the Projector Image Height The projector is equipped with an elevator foot for adjusting the image height. To raise the image: 1. Raise the image to the desired height angle 2 , then release the button to lock the elevator foot into position. Lower the image, then release the button to lock the elevator foot into position. 1 Elevator Button 2 Elevator Foot 13 . . . English Installation Adjusting the Projector Zoom / Focus You may turn the zoom ring to zoom in or out. To focus the image, rotate the focus ring until the image is clear. The projector will focus at distances from 3. 9 to 32. 8 feet (1. 2 to 10. 0 meters). Zoom Ring Focus Ring Adjusting Projection Image Size 275. 00 220. 00 192. 50 229. 17 183. 33 160. 42 114. 58 68. 75 27. 50 137. 5 82. 50 33. 00 3. 94'(1. 2m) 9. 84'(3. 0m) 16. 40'(5. 0m) 22. 97'(7. 0m) 26. 25'(8. 0m) 32. 81'(10. 0m) PROJECTION DISTANCE (METER) 4 : 3 SCREEN SIZE - DIAGONAL (INCH) Tele 27. 50 34. 38 45. 83 50. 42 68. 75 91. 67 114. 58 137. 50 160. 42 183. 33 206. 25 229. 17 275. 00 Wide 33. 00 41. 25 55. 00 60. 50 82. 50 110. 00 137. 50 165. 00 192. 50 220. 00 247. 50 275. 00 330. 00 1. 2 1. 5 2 2. 2 3 4 5 6 7 8 9 10 12 This graph is for user's reference only. English. . . 14 User Controls Control Panel & Remote Control There are two ways for you to control the functions: Remote Control and Control Panel. Control Panel Remote Control Using the Control Panel Refer to the "Power On/Off the Projector" section on pages 11-12. Source Press "Source" to choose RGB, Component-p, Component-i, S-Video, Composite Video and HDTV sources. Menu Press "Menu" to launch the on screen display (OSD) menu. To exit OSD, press "Menu" again. Four Directional Select Keys Use selection. Press the to increase the amount of green in the image. Press the to increase the amount of red in the image. "Saturation" and"Tint" functions are not supported under computer mode. Color R Adjusts the red color. Color G Adjusts the green color. Color B Adjusts the blue color. English. . . 20 User Controls Image (Computer Mode) Keystone Adjust image distortion caused by tilting projection. ( 15 degrees) Aspect Ratio Use this function to choose your desired aspect ratio. 4:3 : The input source will be scaled to fit the projection screen. 16:9 : The input source will be scaled to fit the width of the screen. Auto : Keep the image with original width-higth ratio and maximize the image to fit native horizontal or vertical pixels. 16:9 Image Postion H. Position (Horizontal Position) V. Position (Vertical Position) Frequency Press the Press the Press the Press the Press the to choose the image position showed on top, center, or bottom. to move the image right. to move the image down. to move the image up. "Frequency"changes the display data frequency to match the frequency of your computer's graphic card. If you experience a vertical flickering bar, use this function to make an adjustment. Tracking "Tracking" synchronizes the signal timing of the display with the graphic card. [. . . ] Select "Management" from the OSD and adjust the projection direction. Problem: Lamp burns out or makes a popping sound When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp". [. . . ]