User manual ACER VERITON X4610

[. . . ] This guide contains procedures for replacing the following parts: · Memorymodules · Harddiskdrive · Opticaldrive · Keyboard, Mouse(wired) · Powercord Safety information for replacing CRUs Do not open your computer or attempt any repairs before reading the "Important safety information" in the Safety and Warranty Guide that was included with your computer. If you no longer have this copy of the Safety and Warranty Guide, you can obtain one online from the Support Web site at http://consumersupport. lenovo. com. Additional information resources If you have Internet access, the most up-to-date information for your computer is available from the World Wide Web. Hardware Replacement Guide 1 You can find the following information: · CRUremovalandinstallationinformation · Publications · Troubleshootinginformation · Partsinformation · Linkstootherusefulsourcesofinformation To access this information, go to: http://consumersupport. lenovo. com Tools required To disassemble the computer, you need the following tools: · Wristgroundingstrapandconductivematforpreventingelectrostatic discharge · Flatscrewdriver · Phillipsscrewdriver · Hexscrewdriver · Plasticflatscrewdriver · Plastictweezers Note: Thescrewsforthedifferentcomponentsvaryinsize. Duringthe disassembly procedure, group the screws with their corresponding components to avoid a mismatch when replacing the components. Handling static-sensitive devices Static electricity, although harmless to you, can seriously damage computer components. When you are replacing a part, do not open the static-protective package containing the new part until the defective part has been removed from the computer and you are ready to install the new part. When you handle parts and other computer components, take these precautions to avoid static-electricity damage: · Limityourmovement. Movementcancausestatic-electricitytobuilduparound you. 2 Hardware Replacement Guide · Alwayshandlepartsandothercomputercomponentscarefully. Handle adapters, memory modules, system boards, and microprocessors by the edges. [. . . ] Unplug all power cords from electrical outlets. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to "Left and right view" and "Rear view" for help with locating the various connectors. Removethe2coverpiecesbyslidingtheminoppositedirectionsasshown. 10 Hardware Replacement Guide Mounting the computer onto a wall Thecomputercanbemountedontoawall. Beforedoingthis, youwillfirstneedto install a wall mount VESA bracket adapter* (some models are shipped with this part) onto the back of the computer. The bracket adapter can then be used with a UL listed standard wall mount (to be purchased separately) to mount the computer onto a wall. To install a wall mount bracket adapter Note: Itmaybehelpfultoplacethecomputerface-downonasoftflatsurface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the touch screen from scratching or other damage. Remove the 2 cover pieces by sliding them in opposite directions as shown. * VESA bracket adapter spec: VESA100, 100mm x 100mm, M4 bolts. Hardware Replacement Guide 11 2. Remove the 6 screws that secure the stand to the computer, and then slide the stand out. 3. Align the wall mount bracket adapter and slide into place as shown, and then secure the adapter to the computer with the 6 screws. 12 Hardware Replacement Guide 4. Slidebothcoverpiecesbackintoposition. Replacing a memory module Attention: Turn off the computer and wait 3 to 5 minutes to let the computer cool down before removing the computer cover. Pushasmallironstick(paperclip)intothesmallholeontheopticaldrivecover so that the disk springs out as shown. 8. Remove the 2 screws that secure the optical drive to the metal bracket. Useasmallflatheadscrewdrivertopressandpushoutthepinsthatsecure the cover to the disk. Separate the cover from the defective optical drive. 16 Hardware Replacement Guide 11. Install the new optical drive as follows: (1) Align the new optical drive with the cover, and then push the cover back into position. (2) Screw the metal bracket back onto the new optical drive. (3) Slide the new optical drive into the drive bay. Screw the new optical drive back onto the chassis. Slide the computer cover back into position. Replacing the hard disk drive Attention: Turn off the computer and wait 3 to 5 minutes to let the computer cool down before replacing the hard disk drive. To replace the hard disk drive: Note: Itmaybehelpfultoplacethecomputerface-downonasoftflatsurface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the screen from scratching or other damage. Refer to "Removing the computer cover". [. . . ] Changes are made periodically to the information herein; these changes will be incorporated in new editions of the publication. To provide better service, Lenovo reserves the right to improve and/or modify the products and software programs described in the manuals included with your computer, and the content of the manual, at any time without additional notice. The manuals included with your computer are provided to help you use Lenovo's products appropriately. For the configuration of the product, refer to the related contract (if any) or product packing list, or consult the distributor for the product sales. The content of the manuals included with your computer is protected by copyright laws and rules. [. . . ]