User manual ACER X1311WH

[. . . ] Use the attached RGB cable, RS-232C cable with this equipment so as to keep interference within the limit of a FCC Class B device. DO NOT LOOK DIRECTLY INTO THE LENS WHEN PROJECTOR IS IN THE POWER ON MODE. When using the projector in Europe COMPLIANCE NOTICE This LCD - Video Projector complies with the requirements of the EC Directive 89/336/EEC "EMC Directive" as amended by Directive 93/68/EEC and 73/23/EEC "Low Voltage Directive" as amended by Directive 93/68/EEC. The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on small-scale enterprises, inside as well as outside of the buildings. [. . . ] Use to change the brightness of the lamp. When LOW is selected, the image will become darker, though the power will be saved, operating sound will be reduced. · The intensity of the lamp will be STANDARD for 2 minutes regardless of the setting of the LAMP MODE when the lamp turns on. · When the LAMP MODE is changed, the screen may flicker. Use to reverse or invert the projected image. Select MIRROR, INVERT in rear projection with the projector hanging from the ceiling. · When no signal is supplied for 6 hours with BACK COLOR set to BLACK, it changes to BLUE automatically for the purpose of protecting the projector. · When you continue projection for a long time with BACK COLOR or MUTE set to LOGO, an after-image may persist on the screen. · When the signal is lost during muting with MUTE set to LOGO, AUTO POWER OFF is ignored even though it is active. ON EN ­ 16 3 FEATURE MENU POSITION . . . . . . . Use to select the position of the menu on the screen, (upper left) or (lower right). When AUTO is selected, the appropriate video format is automatically selected depending on the input signal. Use to synchronize the projector with PC input signals so that the image is not blurred. Use to avoid image noise such as wide stripes. The unit adjusts itself automatically when connected to a DVD player with a component video output (Y, CB, CR). In the case the projector is connected to equipment that includes RGB output terminal, adjust to RGB mode. Adjusts the image when flagging occurs near the top of the screen. XGA60 AUTO 0 0 0 0 RGB AUTO SIGNAL A U MEMORY CALL HORIZ. TRACKING RGB RGB COMPUTER INPUT HOLD USER MEMORIZE DELETE DEFAULT 5 SIGNAL - USER (Normally, there is no need for adjustments. ) SIGNAL-USER CLAMP POSITION/ CLAMP WIDTH . . . . . . . . . . If you use something similar, the brighter colors of the projected CLAMP POSITION image may become blurred. In this case, adjust CLAMP POSITION CLAMP WIDTH or CLAMP WIDTH. (Adjust to the horizontal pixels of the input VERT. signal for normal setting. ) VERT. LINES . . . . . . . The image size grows higher SHUTTER(U) as the number increases. [. . . ] 30 30 5F 72 31 0D '0' '0' '_' 'r' '1' ' ' 30 30 5F 72 31 0D '0' '0' '_' 'r' '1' ' ' Status code from the projector Description Command for setting the input signal to COMPUTER 1 Command receipt confirmation (Command echo back) 5) Volume commands (Not executable in stand-by mode, while the Splash screen is projected or the MUTE is executed. ) The volume commands are used for the volume setting of this projector with the value. ITEM VOLUME ASCII VL HEX 56h 4Ch VALUE 00 - 31 How to set the grade Use the ASCII codes to set the grade for setting data. Please refer to the table below for the HEX code. ASCII '0' '1' '2' '3' '4' '5' '6' '7' '8' '9' HEX 30h 31h 32h 33h 34h 35h 36h 37h 38h 39h [Example] When setting the volume to 15 (standard value) (Figures and symbols enclosed in quotation marks are ASCII codes. ): Sending commands from the PC, etc. 30 30 56 4C 31 35 0D '0' '0' 'V' 'L' '1' '5' ' ' 30 30 56 4C 31 35 0D '0' '0' 'V' 'L' '1' '5' ' ' Command receipt confirmation (Command echo back) Status code from the projector Command for setting the volume Description 2 6) Keystone commands (Not executable in stand-by mode, while the Splash screen is projected or the MUTE is executed. ) The keystone commands are used for the keystone setting of this projector with the value. [. . . ]