User manual ACOUSTIC ENERGY AEGO 5

[. . . ] English Technical Information Satellite Speakers: A patented advanced technology driver featuring a unique heat transfer system: special high excursion suspension and a computer-designed anti-resonant cone Power ratings: 120V Model - 120V @ 60Hz; 80VA 240V Model - 140V @ 50Hz; 80VA Dimensions: Inputs: 3 x RCA Phono - Line level 1 x Stereo Mini jack - Line level Sub Woofer - 265mm x 190mm x 350mm Satellites - 68mm x 103mm x 90mm Weight: Outputs: 3 x Speaker terminals 9 Kg Finishes: Controls: 1 x Volume / Power pot 1 x Bass switch (3 Position) 1 x Centre input switch (2 Position) Black sub woofer Textured black satellites with silver/grey grilles White sub woofer Textured white satellites with silver/grey grilles Accessories: 2 x 5 metre Speaker cables 1 x 2 metre Signal input cable 1 x Speaker level to line level adaptor cable 2 x Wall brackets Warranty Your Acoustic Energy loudspeakers are guaranteed against original defects in materials, manufacture and workmanship for 1 year from the date of purchase. Please retain all original packaging materials for possible future use. Under this warranty Acoustic Energy agrees to repair any defect or, at the company's discretion, replace the faulty component(s) without charge for parts and labour. This warranty does not imply any acceptance by Acoustic Energy or its agents for consequential loss damage and specifically excludes fair wear and tear, accident misuse or unauthorised modification. [. . . ] Shielded cables and I/O cords must be used for this equipment to comply with the relevant FCC regulations. 1. After properly connecting AEGOP5 to your audio sources and amplifier, plug in AEGOP5 's AC adapter to an AC outlet. Turn on the power of AEGOP5 by pushing the POWER button on the front panel. Turn on the power of all audio sources, amplifier, or powered subwoofer. Installation is now complete, get ready to experience true Dolby Digital or DTS surround sound. Note: To prevent damage to speakers, when playing music or a movie, ensure the volume is set low initially. Gradually turn the volume up to an appropriate level after the playback has started. Volume knob This is the main volume control for all channels. LS/RS Button simultaneously activates/deactivates the left and right rear speakers. SW Button activates/deactivates the subwoofer. MULTIPIN Developed And Manufactured By Videologic Systems. AEGOp5 Rear Panel 1. MULTIPIN Audio Output: This output feeds 6 channels audio signals to the matching input on a control centre or power amplifier via a multipin (DIN) cable. Main Outputs (Front Left, Front Right, Rear Left, Rear Right, Centre and Sub): The Six outputs feed audio signals to the matching inputs on a control centre or power amplifier. AUX1 AUX2 and LINE Inputs: These inputs accept signals from stereo analog signal sources. OPTICAL and DIGITAL inputs: Your AEGOP5 has two types of digital inputs. One S/PDIF (OPTICAL) and one coaxial (DIGITAL) input. Connect the digital outputs of the sound sources to these inputs. 12V DC Power Input: Connect the AEGOP5 power adapter to an AC outlet. Please refer to page 6 to determine the correct voltage in your area. 15 BASS MANAGER Button Switches between three bass configurations (bass config. 1, bass config. 2 and bass config. 3) 16 VOL + and VOL Increase/decrease the volume. 17 D TIME Button Increase/decrease the delay time. 18 DRC Button Select among 3 different dynamic range compression ratios. 19 RESET Button Resets the system to its factory default settings. 8 9 AEGOp5 Operation The following pages provide information on the operation of AEGOP5. The AEGOP5 was purposely designed to be simple to operate with all functions available from the remote control. AEGOp5 Operation AEGOP5 Operation - Test Mode Test Mode After connecting up to your source and speakers, you can press the TEST button on the remote to test the system. You can also use the test mode to test the location of the speakers. When the TEST button is pressed, white noise is generated through all satellite speakers in an order of Front Left, Centre, Front Right, Rear Left, and Rear Right channels for 2 seconds each. When completed, the AEGOP5 returns to Auto Decode mode. AEGOp5 Operation - Input Selection Input Selection The AEGOP5 can be connected to up to 5 audio sources. Select the input source you want by repeatedly pressing the INPUT Button on the remote control until the desired source is selected. AEGOp5 Operation - Master Volume Control Volume Setting To increase or decrease the master volume of your AEGOP5, simply press VOL + or VOL - on the remote control. preset 1 preset 2 preset 3 AEGOp5 Operation - LCD and LEDs 1. Press the power button to turn the AEGOP5 on, press it again to turn it off. [. . . ] Increase the time delay of the surround speakers by pressing D TIME + until you are able to hear a 3D sound effect coming from surround speakers. Press DELAY Button again to move to the next channel. DOLBY DIGITAL CO PROLOGIC DISABLE DOLBY DIGITAL CO BASS CONFIG. 2 Bass Config. 3 With this setting, the bass signal below 120Hz will be sent to all the speakers; the LEDs on the front panel indicating L/R/SL/SR/SW channels will be red and the LCD will show the following information: AEGOp5 Operation - Speaker Mode with Bass Manager Speaker Mode with Bass Manager The six LEDs on front panel of your AEGOP5 represent the six discrete audio channels (Left, Right, Centre, Rear Left, Rear Right and Sub). If a particular channel is active, the LED will light up in green. The LED will be red if that particular channel carries bass signal below 120Hz. [. . . ]