User manual ACR ELECTRONICS CC-1 REV C

[. . . ] Customizing the Activation Code . . . . . . . . . . . . . . . . . . . . . . . . . . 8 6. 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Code Configuration Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 FIGURE DESCRIPTION PAGE 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Lenses in color or IR transmitting are available. The ACR/L-32 light may be used alone or in combination with Items 2, 3 and 4 below, for Remote Radio Frequency control. The Model ACR/L-32RC Remote Control Unit (See Figure 2) The ACR/L-32RC remote control is designed to be installed between the ACR/L-32 light and the battery. The remote control is a FM receiver that will supply power to the light when it receives the proper "ON" code. It will shut off power to the light when it receives the proper "OFF" code. Selection of the turn "ON" turn "OFF" codes is made by removing the ACR/L-32RC cover and moving the mini-switches to the desired codes. Code Seven (7) is not switch selectable, but will always shut off all lights. The standard FM Frequency of the remote control is 46. 75 MHz. The ACR/L-32RCL Remote Controlled Light (See Figure 3) The ACR/L-32RCL, Remote Controlled Light is a combination of the technology of the L-32 and the L-32RC. These two have been combined into one unit the size of a single L-32. The ACR/L-32RCL is plugged directly into the battery, the switch is designed to change the light from "Remote Controlled Mode" to "Manual Mode". The Model ACR/CC-1 Code Controller (See Figure 4) The ACR/CC-1 Code Controller is designed to interface with the PRC-77 Handset Microphone. It is a hand held tone generator which is used to send tone codes through the PRC-77. When using the ACR/CC-1, place it in direct contact with the microphone of the handset. Press the desired code on the CC-1 (you will hear the tone). Then key the microphone, instantly the light should respond. PRC-77 or an Equivalent FM Transmitter Shall be capable of transmitting FM signals on frequency of 46. 75 MHz. (Not provided) Figure 2 ACR / L-32 RC Remote Control 4 Y1-03-0116 Rev. C 4. 0 SYSTEM SET-UP AND OPERATION A) Manual Activation 1) Insert the ACR/L-32 or ACR/L-32 RCL Light into a BA-4386 or BA-5598 Battery. 2) Press the Push-ON, Push-OFF switch for the desired position (light will turn ON or OFF accordingly). 3) Repeat steps 1 and 2 for all additional lights. (Each light must have its own battery. ) Figure 3 ACR / L-32 RCL Remote Controlled Light B) Remote Control Activation of the ACR/L-32, ACR/L-32RC Combination (See Figure 5) 1) Set the ACR/L-32 to ON position (see steps 1 and 2 of Manual Activation). [. . . ] C) Setting the "ON" code selector Set the DIP switches of the "ON" code selector to the "ON" position for desired "ON" activation code. Set all other DIP switches to "OFF" position. 9 Y1-03-0116 Rev. C ON ON Example 1: Light shall turn "ON" when code 1 is selected. Set-up: Set DIP switch number 1 to "ON" position (away from the case wall), set all others (2, 3, 4, 5, and 6) to "OFF" position (toward the case wall). D) Setting the "OFF" code selector Set the DIP switches of the "OFF" code selector to the "ON" position for desired "OFF" activation code(s). [. . . ]