User manual ACT ACTSMART PRODUCT RANGE

[. . . ] Operating & Installation Instructions for ACTSmart Product Range ACTSmart Operating and Installation Manual Rev 1. 1 Contents Installation Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Second Programming Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Programming Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Each unit also has built-in tamper monitoring for improved security. ACTSmart Programming Press the button followed by the programming code (initially 9999). The LED will flash amber while in programming mode. If is pressed at any time or no key is pressed within 30 seconds, programming mode is exited. If the LED flashes green during programming, then a card presentation is expected. If the LED flashes red, then a keypress is expected. If the ACTSmart is busy performing a task, (Eg. Defaulting memory, adding cards), the buzzer will sound an elongated tone. Note: In most Programming Menus there is a step that is marked (optional)*. This setting only applies to a Networked System (see Programming a Network System). -6- ACTSmart Operating and Installation Manual Rev 1. 1 Adding a Card Batch: Step Keypad Entry 1 10 2 Present Card 3 Present Card 4 Enter 1-8, (optional)* 5 Press Deleting a Card Batch: Step Keypad Entry 1 11 2 Present Card 3 Present Card 4 Enter 1-8, (optional)* 5 Press Adding a PIN: Step Keypad Entry 1 12 2 0001-9999 3 1-8, (optional)* 4 Press Deleting a PIN: Step Keypad Entry 1 13 2 0001-9999 3 1-8, (optional)* 4 Press Adding a Card and PIN: Step Keypad Entry 1 14 2 Present Card 3 0001-9999 4 1-8 (optional)* 5 Press Deleting a Card and PIN: Step Keypad Entry 1 15 2 Present Card 3 1-8, (optional)* 4 Press Operation Add Card Batch First card in Batch (lowest number card) Last Card in Batch (highest number card) Select each door this batch enabled for End programming card batch ­ Note: the buzzer will sound while cards are loaded into memory. Operation Delete Card Batch First card in Batch (lowest number card) Last Card in Batch (highest number card) Select each door this batch deleted from End delete card batch­ Note: the buzzer will sound while cards are deleted from memory. Operation Add PINs (Make sure Option 40 is set on PIN and Prox units. ) 4 - 8 digit PIN code Select each door this PIN is valid for End programming PINs Operation Delete PINs 4 - 8 digit PIN code Select each door this PIN is deleted from End deleting PINs Operation Add Card and PIN (Make sure Option 39 is set on PIN and Prox units. ) 4 - 8 digit PIN code Select each door this Card & PIN is valid for End programming Card and PINs Operation Delete Card and PIN Select each door this Card & PIN is deleted from End deleting Card and PINs -7- ACTSmart Operating and Installation Manual Rev 1. 1 Adding a Card Batch using the keypad: Step Keypad Entry Operation 1 16 Add Card Batch 2 Enter 10-digit card number 10-digit First Card number with leading zeros. 3 Enter 10-digit card number Second Card number 4 1-8, (optional)* Select each door this Card is deleted from 5 Press End Adding Card Batch Deleting a Card or Card and PIN using the keypad: Step Keypad Entry Operation 1 17 Delete Card or Card and PIN 2 Enter 10-digit card number 10-digit Card number with leading zeros. 3 1-8, (optional)* Select each door this Card is deleted from 4 Press End deleting Card (Card and PIN) Set Door Relay Time: Step Keypad Entry 1 20 2 Enter 3 digit time 3 1-8 (optional)* 4 Press Set Door Ajar Time: Step Keypad Entry 1 21 2 Enter 3 digit time 3 1-8 (optional)* 4 Press Set Guest Buzzer Time: Step Keypad Entry 1 22 2 Enter 3 digit time 3 1-8 (optional)* 4 Press Change Programming Code: Step Keypad Entry 1 23 2 0001-9999 Operation Set Door Relay Time ­ (default 5 seconds) 000-255 seconds ­ (leading zeros required). Select each door this timer is set for End setting Door Relay Timer Operation Set Door Ajar Time ­ (default 30 seconds) 000-255 seconds ­ (leading zeros required). Select each door this timer is set for End setting Door Ajar Time Operation Set Guest Buzzer Time ­ (default 2 seconds) 000-255 seconds ­ (leading zeros required). Select each door this timer is set for End setting Guest Buzzer Time Operation Change Programming code New 4 - 8 digit programming code Change Number of PIN Digits: Step Keypad Entry Operation 1 24 Change Number of PIN digits 2 4-8 Select number of PIN digits in range 4 to 8. When set, the codes require leading zeros Eg. Set one device on the network to be the Master. When set, only Card and PIN users are admitted. This is only valid for ACTSmart PIN and Prox units. When set, either a valid Card or valid PIN will open the door. This is only valid for ACTSmart PIN and Prox units. In this mode, a valid card and any valid PIN code will open the door. This is only valid for ACTSmart PIN and Prox units. [. . . ] Release the key and then enter the default Programming Code (9999). During this time, the buzzer will sound an elongated tone. Restoring Factory Defaults - 13 - ACTSmart Operating and Installation Manual Rev 1. 1 To program an ACTSmart Prox Only device, a Programming Card must be assigned to the ACTSmart. The Programming Card may be any proximity card. If you have a received a batch of cards, use the first (lowest numbered) card in the batch as the Programming Card. [. . . ]