User manual ACT PRO MIFARE CLASSIC READERS

[. . . ] Operating & Installation Instructions for ACTpro MIFARE Classic Readers 18-00070 ACTpro MIFARE classic Operating and Installation Manual Rev 1. 0 Contents ABOUT MIFARE CLASSIC (STANDARD). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 INSTALLATION NOTES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 PRODUCT SPECIFICATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ORDERING INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 READER OUTPUT DATA FORMAT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 WIRING INFORMATION FOR "CLOCK & DATA" OUTPUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 WIRING INFORMATION FOR "WIEGAND" OUTPUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 READER CONFIGURATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 SECTOR READER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 SERIAL AND REVERSE SERIAL READER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 BACKLIGHT OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 READER CONFIGURATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 POWER ON BEEP CODES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 READER REPROGRAMMING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 MOUNTING INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 MIFARE PANEL MOUNT INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1 ACTpro MIFARE classic Operating and Installation Manual Rev 1. 0 About MIFARE Classic (Standard) MIFARE Classic cards are widely used for electronic wallet (cashless vending), access control, corporate ID cards, transportation, stadium ticketing, etc. The memory on the MIFARE Classic card is divided into sectors and blocks. [. . . ] The default position of the jumper is set for sector operation (jumper on pins 1 and 2). To change the operation down power the reader, change the jumper for the desired operation and reapply power. Sector Serial Reverse Serial Sector / Serial Operation Jumper Connect pins 1&2 Connect pins 2&3 Do NOT connect Jumper Operation: ACTpro MIFARE 1030 The operation of the ACTpro MIFARE classic 1030 is selectable via cable configuration, the default setting is Sector where both Orange and Purple cables are connected to 0V. To change the operation down power the reader, change the Orange and Purple cable for the desired operation and reapply power. Colour Orange Purple Sector 0V 0V Serial 0V Not Connected Reverse Serial Not Connected 0V Sector Reader The default sector reader operation of ACTpro MIFARE readers is to read the batch numbers that are encoded into Sector 1 from the MIFARE cards and fobs issued by ACT. However the readers can be programmed to read any specified sector data, this allows the readers to be installed on sites that are already using MIFARE cards. See section on reader re-programming. Serial and Reverse serial Reader When in Serial or reverse serial mode the MIFARE card serial number is read by the reader. 5 ACTpro MIFARE classic Operating and Installation Manual Rev 1. 0 Backlight Operation The ACTpro MIFARE 1050 has backlight illumination of the keypad. The default operation is for the illumination to be switched on all the time. During installation the back light operation may be switched off or changed to automatic. In automatic mode the keypad is illuminated for 20 seconds on a key press or when a card is presented to the reader. To change the backlight operation: Firstly power up the reader, the LED on the top right hand side will cycle through green, blue and red and back to blue, while the LED is red enter the code below for the required operation. The code must be completely entered while the LED is red. ·Always on (Default):X014000 ·Always Off:X014001 ·Automatic:X014008 Note: the backlight operation for the ACTpro MIFARE 1030PM is controlled by jumpers marked LED. Reader Configuration The Internal buzzer is activated by applying 0V to the Buzz PIN. The buzzer activates 4 seconds after the 0V is applied and sounds continuously until the 0V is removed (External Buzzer Control not available on the ACTpro MIFARE 1030) reader. The Red and Green LED are activated by applying 0V to the respective Red and Green input pins. Power On Beep Codes The Output Data Format and the Sector/Serial Operation of the reader can be determined by the beeps generated by the reader after power is applied. [. . . ] The ACTpro MIFARE will acknowledge the re-programming by playing an ascending note tune. The configuration is held in non-volatile memory and so is held even if the reader is powered down. Readers that have been reprogrammed may be reset to read ACT issued MIFARE cards and fobs with an ACT Default Programming Card. ACTpro MIFARE readers that have been programmed to read non ACT MIFARE cards and fobs will play a series of ascending notes after being powered up in addition to the standard beep codes, this is to indicate that it no longer reads the MIFARE cards and fobs issued by ACT. Please see the "Application for an ACTpro MIFARE reader programming card" document for details on obtaining a programming card. 7 ACTpro MIFARE classic Operating and Installation Manual Rev 1. 0 Mounting Instructions Flush Mount Unit Surface Mount Unit 8 ACTpro MIFARE classic Operating and Installation Manual Rev 1. 0 Installation diagram for MIFARE Panel Mount Reader Rear view of the ACTpro MIFARE Panel Mount reader connection to the ACTpro Door Controllers & Door Stations 9 [. . . ]