User manual ADDONICS HDUSI5TDR

[. . . ] While duplication process is on-going, allows you to plug-in additional target drives and duplication will automatically start for the added target drive. Choose option 2 from the menu: Press ENT to begin copy. The system will auto-detect the hard disks and show the following info on the LCD. If the duplicator detects a drive whose capacity is less than the source drive, the th LCD will display the corresponding channel number. For example, the 5 drive. The LCD will show the following info during the copying process: remaining time, completed percentage. [. . . ] Press ENT to confirm and save the changes. Press ENT to begin scanning IDEO0:Master/Save ~ IDE1:Master/Slave. When the scan is complete the LCD will display the following info. 8. 3 Startup Menu This option allows you to set an option other than "Setup" to be displayed as the first available option on the menu every time you start the system. 8. 8 Fast Copy This option displays Fast Copy. Fast Copy only copies data on the source drive to the target drives. Press ENT then use the Up and Down arrow keys to choose other options. By default the first menu option is Copy HDD. Press ENT and the LCD will display the following info. Use the Up and Down arrow keys to choose whether fast copy is on or off. (This function currently only supported in FAT, FAT32, NTFS, HFS, Ext2 and Ext3 partitions. ) 8. 4 Auto Compare This option automatically compares the source hard disk with the target hard disk after a copy operation is completed. 8. 9 Auto Start Drive This option is used to copy automatically once you inserted a HDD on target port. Press ENT to access option. Use the Up and Down arrow keys to choose On. Press ENT to enter the following figure. Use the Up and Down arrow keys to choose 1-5. 8. 5 Button Sound 8. 10 Auto Start Timer This option is used to set the period of time when the duplicator starts copying automatically once you insert HDD on target port. Press ENT and the LCD will display the following info. Use the Up and Down arrow keys to choose whether button sound is on or off. Press ENT to enter the following figure. Use the Up and Down arrow keys to choose 5 Sec-50 Sec. 8. 6 Device Info This option is used to display the details of all hard disks connected to the copy controller. 8. 11 Tolerance Size This option is used to set the tolerance in terms of percentage the difference in the source and target capacity. This is to ensure that when the target drive is smaller than the source drive, the duplication process will not start. Press ENT and the LCD will display each hard disk' information in order as shown below. Press ENT to enter the following figure. Use the Up and Down arrow keys to choose 1%~100% of source. 8. 7 System Info This option displays system information. 8. 12 BootTime Delay This option is used to set boot delay time. Appendix A LCD Messages Press ENT to enter the following figure. Use the Up and Down arrow keys to choose 0~99 sec. 5. 8. 13 Quick Compare This option is used to set the size of each comparison unit. Press ENT to enter the following figure. Use the Up and Down arrow keys to choose 1 Byte/1K/10K/100K/1MB/10MB/100 Mbytes. (In order to improve the accuracy of pure data can maintain the default settings. ) Connecting with a HDD: All data will be lost, format?. . . . . . . . . . . . . Delete Image in Partition xx?. . . . . . . . . . . . . Confirm the deleting of data image in partition xx. Format HDD?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ask if you want to format the hard disk. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The Formatting of hard disk has been completed. HDD not Format!. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The hard disk hasn't been formatted yet. HDD too small . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Source can't be Hard Disk!. . . . . . . . . . . . . . . . . . . . . During comparison the source cannot be hard disk. Basic Troubleshooting 9. 1 LCD If the LCD display is blank after the device is turned on, check that the power cable is properly connected and that the power supply is on. 9. 2 Error Message When the system is running a copy operation or hardware diagnostics then operation was manually terminated by pressing ESC, an error message will be shown by the LCD. This may lead to an illegal operation and cause the device to stop reminding. If this happens, the device must be restarted. [. . . ]