User manual ADE ACCENTA MERCURY

[. . . ] Program 2 To protect the perimeter of the property in the evening and become Set after say 20 seconds. Program 3 To protect the downstairs areas of the house at night and become Set silently. The installer has the ability at the programming stage to configure all the circuits to the customer's exact requirements. ÿ ÿ User 1 code - 0123 factory set User 2 code - not programmed. How to operate Personal Attack Personal Attack buttons on the keypad are used to activate the alarm, irrespective of whether the system is armed or not. [. . . ] Press Simultaneously: 9 4 2 4PI175 issue 1_6/01 Accenta/Optima G3 intruder system Operating instructions How to set the system (on program 1) The green Day indicator should be showing. Day Enter your code number and check n n n n that the system is clear (none of the 10seconds Exit beep insistent beeps zone indicators are showing). The Day sounder will now produce an exit o/p ARC beep tone and you Set output should leave by the approved route. The system will Set as the beep tone stops. How to unset the system (turn off) On entering the premises an entry beep tone comes on. Enter your code, the green Day indicator is lit. The system is unset and disarmed. Entry beep Day Acknowledge Day Push to Set Switch In some systems a Push to Set switch may be fitted outside the premises near to the main exit door. This should be used to complete the setting procedure once the building has been vacated. As the switch is operated, the exit beep tone will stop and a chime tone will be produced to acknowledge setting. o/p ARC Unset output How to set program1, 2 or 3 The green Day indicator should be showing. Day Enter your code number and the n n n n exit beep tone will start. The external sounders will pulse on and off at 2 second intervals and all keypad indicators will flash to attract attention. Chime is a low security monitoring system for use when the system is Unset. When a zone that is set to chime is operated, the internal sounder will produce a low volume two stage warning tone and the Zone indicator will show. The indicator may be cancelled by pressing Reset. Chime is particularly useful in a shop to warn of a customer presence or in a house to warn that a door or particular area has been accessed. Any zone may set to be on or off chime by pressing the CHIME key and then keying in the required zone number(s). After a few seconds the system will automatically return to the Day mode. 4PI175 issue 1_6/01 4 Accenta/Optima G3 intruder system Operating instructions Operator's Program mode The information below shows the programmable options available and how to change them. Once the programming mode has been accessed, each section may be changed in any order. As each operation is completed the system will automatically return to top level of program mode. How to view the event log The panel can hold up to 8 previous events which can be scrolled automatically or manually. The automatic scroll starts with the newest event ( number 8) to the oldest one ( number 1). Example: To view up to 8 previous events and thereafter to stop the event scroll, Press: Prog 0 1 2 3 Chime Reset Note: When programming the system should be in the Day mode, with the Day and Power indicators lit. Enter Operator's program mode Chime View the event log Tamper To exit operation at any time On pressing the Reset key you will quit the current level of operation. Reset Automatic event scroll Starting from event 1 to 8 To manually scroll View event 1 1 (oldest event) 2 3 Zone, PA and Tamper indicators will be lit to show zone in alarm. [. . . ] As each operation is completed the system will automatically return to top level of program mode. How to view the event log The panel can hold up to 8 previous events which can be scrolled automatically or manually. The automatic scroll starts with the newest event ( number 8) to the oldest one ( number 1). Example: To view up to 8 previous events and thereafter to stop the event scroll, Press: Prog 0 1 2 3 Chime Reset Note: When programming the system should be in the Day mode, with the Day and Power indicators lit. Enter Operator's program mode Chime View the event log Tamper To exit operation at any time On pressing the Reset key you will quit the current level of operation. Reset Automatic event scroll Starting from event 1 to 8 To manually scroll View event 1 1 (oldest event) 2 3 Zone, PA and Tamper indicators will be lit to show zone in alarm. Flashing indicates the first zone in alarm. [. . . ]