User manual ADE OPTIMA G3 INTRUDER SYSTEM

[. . . ] In each Program the exit mode can be changed and the zone may be set up to have a different function. The examples below show how 3 typical Programs could be used in a house. Program 1 To arm all of the zones and become Set as the user leaves the property and closes the final door. [. . . ] Day Enter your code number and the n n n n exit beep tone will start. Press Exit beep the Prog key and ZONE 1-3 Prog Exit beep the exit tone will stop. Press 1, 2 2 Or 3 1 or 3 for the required 10 seconds Exit beep insistent beeps program, the sounder will Day beep to o/p ARC acknowledge the Set output program number. The exit beep tone will start and you should leave by the approved route. The system will Set as the beep tone stops. It is important that you follow the correct procedure when setting the system. After leaving the protected area it is absolutely essential that you wait until the exit tone stops, before assuming the system has set. Keyswitch Set Your system may have been fitted with a remote keyswitch. This can be used as an alternative to arming the system with a code and will set Program 1. Where a keyswitch is used it may be necessary on occasions to allow it to catch up with the system. For example if the alarm was set with a code, to Unset with the keyswitch, it would have to be momentarily turned to Set then returned to Unset. Faults during setting If the system is not clear when you try to Set it, the sounder will produce an open zone tone and the fault will be displayed. Either re-enter your code to turn off and investigate or omit the faulty zone(s) from the system. 4PI175 issue 1_6/01 3 How to set the system (on program 1) n n n n Operating instructions Accenta/Optima G3 Intruder system How to Quick set During the exit period (on entering User code) Day the system may be Set Set the system or quickly by pressing Set. This removes the exit time Set a Program period. Set 5 seconds insistent beeps Day How to set Chime Zones Example: To set zone 3 and 4 to chime, Press: Chime 3 Day 4 Reset If you omit zones and require Quick Set, you will need to press Set twice. Chime Timeout after 5 seconds if no selection is made Day Chime o/p ARC Set output 0 Deselect all zones (Factory default - no chime) Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8 Appropriate Zone indicator is lit to show chime zone(s) Zone n Chime selected Zone n Chime deselected How to Omit zone(s) on setting system Press number button to select / deselect Zone Chime 1 2 3 4 5 6 7 8 During the exit period after entering User code and selecting a Day program press Set the system or Set a Program and while theOMIT, the exit tone will stop and zones system is setting: that are about to be Omit ZONE(S) TO BE ARMED armed will be displayed. Key in Exit beep the zone number(s) to be omitted which Press the zone(s) n to be omitted will flash to confirm selection. Zone ZONE(S) TO BE OMITTED indicators which show steady are still Set about to be armed. 10 seconds Exit beep insistent beeps When the selection is complete press Day Set and the exit tone o/p ARC will start. Set output If a zone refuses to be omitted, it may be because the engineer has programmed the panel to prevent you from turning off the zone. If in doubt ask your installer for advice. How to Quick set Reset Leave chime mode Day Fire Alarm The fire zone will operate on detection of a fire, whether the system is Set or Unset, when configured as a 24 hour zone, and cause a distinctive internal sounder tone. The external sounders will pulse on and off at 2 second intervals and all keypad indicators will flash to attract attention. Chime is a low security monitoring system for use when the system is Unset. [. . . ] Day indicates status of panel at the time of alarm Quit the current function Leave Engineering menu Down one menu level View event 2 View event 3 View event 4 View event 5 View event 6 View event 7 How to enter Operator's program mode To enter the Operator's program mode the system should be in Day Prog mode with the Day and ZONE 1 - 8 Power indicator lit. Momentarily On 0 1 2 3 4 5 6 7 8 View event 8 (Newest event) Chime Resume automatic scroll Acknowledge Tamper Day Reset Stop event scroll / view Leave program mode Day Acknowledge Tamper Tamper 4PI175 issue 1_6/01 5 Operator's Program mode Operating instructions Accenta/Optima G3 Intruder system How to create/omit User 2 code User 1 code which is usually considered to be Example: To create user 2 the Managers code 4567, Press: code has the Prog 0 1 2 3 7 authority to add, change or delete 4 5 6 7 Reset the user 2 code. Enter Operator's program mode Change / omit User code 2 7 (By user 1 only) Attack How to create/change/omit the Duress code The Duress code is used in a hold up situation where there is pressure to Set or Unset the system. Entry of the code will allow the system to work normally but also generate a silent PA type alarm by operating the PA communicator output. [. . . ]