User manual ADVANCE ACOUSTIC MPP-506DA QUICK START GUIDE

[. . . ] hEED WARNINGS All warnings on the appliance and in the operating instructions should be adhered to. FOLLOW INSTRUCTIONS All operating and use instructions should be followed. WATER AND MOISTURE The appliance should not be used near water for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. VENTILATION The appliance should be situated so that its location or position does not interfere with its proper ventilation. [. . . ] AUXILIARY 1 AND AUXILIARY 2 INPUTS Press this button to select AUX1 (blue bottom led), press again to select AUX2 (blue top led). eNTRÉES COAXIAL 1 , COAXIAL 2 , OPTICAL ET USB (MPP-506DA) Appuyez sur ce bouton pour sélectionner l'entrée COAX1 (led bleu inférieure) , appuyez à nouveau pour choisir l'entrée COAX2 (led rouge inférieure) , une nouvelle fois pour sélectionner l'entrée OPT (led bleu supérieure) enfin une pression supplémentaire sélectionnera l'entrée USB (led rouge supérieure). COAXIAL 1, COAXIAL 2, OPTICAL AND USB INPUTS (MPP-506DA) Press this button to select COAX1 (blue bottom led), press again to select COAX2 (red bottom led), another time to select OPT (blue top led) and last time to select USB input (red top led) PHONO AND AES/EBU (MPP-506DA) INPUTS Press this button to select PHONO (blue bottom led), press again to select AES/EBU (blue top led). The back panel, you have the possibility to adjust the cartridge type used: MM for moving magnet cartridges and MC for moving coil cartridges. Gh PC RCA, PC JACK AND lp INPUTS Press this button to select the PC RCA (red bottom led), press again to select PC JACK (blue bottom led) and another time to select ip (blue top led). Please note that two inputs connectors for PC JACK and ip are on the front panel, their input levels has been optimised (stereo minijack 3, 5mm). HEADPHONES The headphone terminal provides a stereo audio signal sufficient for driving all conventional stereo headphones except electrostatic headphones which generally require signal from a high level ouputs. VOLUME BUTTON Your amplifier used a rotary type knob to control the 2 channel output sound level (left and right). Turn this volume knob clockwise to increase the ouput sound level and turn this volume knob counterclockwise to decrease the output sound level. ISOLATING SPIKES Your amplifier used spike-feet, you need to use them with non-skid cupels included. The led DAC INSIDE lights up when your preamplifier is a MPP-506DA or a MPP-506 with DAC board inside. To obtain additionnal informations about this upgrade card, please contact your appointed dealer. Your product is designed to be placed on a firm and level surface. Don't place the unit sideways, a big power exerts on the single side of the plate. With this power, the plate will be broken easily. INPUTS You can connect your stereo sources on those inputs. These inputs are suitable for any line level source equipment such as tuners, CD players, DVD, MP3 players, etc. note: These inputs are for analogue audio signals only. They should not be connected to the digital output of a CD player or any other digital device. PHONO INPUT, MM/MC SWITCH AND GROUND TERMINAL You can connect your turntable and adjust the cartridge type (MM or MC cartridge). Turntables normally includes a single wire earth lead. Use the phono ground connector to connect this lead. [. . . ] it was developed by the Audio Engineering Society (AES) and the European Broadcasting Union (EBU) and first published in 1989 (Watkinson , 1989) , later revised in 1995 , 1998 , and 2003. AES3 uses 110 ohm shielded twisted pair (STP) cable with XLR connectors up to a distance of 100 meters. If your source has this type of plug, then you can use it with your MPP-506DA. REC OUTPUT This analog audio input and output are for connecting a recorder with an analog audio input and output, such as a cassette deck, MD recorder, etc. [. . . ]