User manual AEG-ELECTROLUX 68031K-IN 85U

[. . . ] Useful tips and hints Environmental information 2 Contents Operating Instructions. Switching the STOP+GO function on and off. Switching the power function on and off . 4 4 6 6 6 7 8 8 9 9 9 9 10 11 12 13 14 17 18 18 19 20 Cleaning and Care . [. . . ] If a heat setting is set on this cooking zone in addition to a countdown timer, the cooking zone is switched off after the time set has elapsed. Selecting a cooking zone Step 1. Control panel Touch once Display Pilot light of the first cooking zone flashes Pilot light of the second cooking zone flashes Pilot light of the third cooking zone flashes Pilot light of the fourth cooking zone flashes 2. Touch once 3. Touch once 4. Touch once 3 14 The heat setting indicator of the selected cooking zone goes out, as long as the timer time can be set. 3 3 If the pilot light is flashing more slowly, the heat setting indicator appears again and the heat setting can be re-set or modified. Control panel · When the appliance is switched off, if one or more of the sensor fields on the control panel are covered for more that 10 seconds, an acoustic signal sounds. The acoustic signal switches itself off automatically when the sensor fields are no longer covered. Induction cooking zones · In the event of overheating (e. g. when a pan boils dry) the cooking zone automatically switches itself off. Before being used again, the cooking zone must be set to 0 and allowed to cool down. · If cookware that is not suitable is used, flashes in the display and after 2 minutes the display for the cooking zone switches itself off. · If one of the cooking zones is not switched off after a certain time, or if the heat setting is not modified, the relevant cooking zone switches off automatically. Before being used again, the cooking zone must be set to 0. Heat setting V, 1 - 2 3-4 5 6-9 Switches off after 6 hours 5 hours 4 hours 1. 5 hours 17 Tips on Cooking and Frying 3 Information on acrylamides According to the latest scientific knowledge, intensive browning of food, especially in products containing starch, can constitute a health risk due to acrylamides. Wipe the appliance with a damp cloth and a little washing up liquid. Rub the appliance dry using a clean cloth. Remove Type of dirt sugar, food containing sugar plastics, tin foil limescale and water rings fat splashes shiny metallic discolorations imme- when the appliance has diately cooled down yes yes ----------yes yes yes using a scraper* cleaner for glass ceramic or stainless steel* *Scrapers and cleaners for glass ceramic and stainless steel can be purchased in specialist shops 3 3 Remove stubborn residues with a cleaner for glass ceramic or stainless steel. Scratches or dark stains on the glass ceramic that cannot be removed do not however affect the functioning of the appliance. 21 What to do if . . . Problem Possible cause Remedy The appliance cannot be More than 10 seconds have Switch the appliance on switched on or is not oper- passed since the appliance again. ating was switched on The lock is switched on Switch off the lock (See the section "Locking/unlocking the control panel") Deactivate child safety device (See the section "Child safety device") Only touch one sensor field Remove any objects (pan, cloths, etc. ) that are lying on the control panel. Switch the appliance on again Switching off STOP+GO The child safety device is switched on Several sensor fields were touched at the same time Safety cut-out has been triggered STOP+GO is activated The residual heat indicator The cooking zone was only If the cooking zone is supis not displaying anything on for a short time and is posed to be hot, call the therefore not hot Customer Service Department. The automatic warm up function is not switching itself on There is still residual heat on the cooking zone The highest heat setting is set Let the cooking zone cool down The highest heat setting has the same power as the automatic warm up function Uncover sensor field Repeated acoustic signal One or more sensor fields (6x), appliance switches off have been covered for longer than 10 seconds Acoustic signal sounds The control panel is wholly Remove objects. when appliance is switched or partly covered by oboff jects. Acoustic signal sounds and The On/Off sensor field has Do not place any objects appliance switches itself on been covered up, e. g. by a on the control panel and then off again; after 5 cloth seconds another acoustic signal sounds 22 Problem Display is switching between two heat settings flashes Possible cause Power management is reducing the power of this cooking zone Unsuitable cookware No cookware on the cooking zone Remedy See the section "Switching the power function on and off" Use suitable cookware Place cookware on the cooking zone The diameter of the botMove onto a smaller cooktom of the cookware is too ing zone small for the cooking zone Use suitable cookware is lit Overheating protection for Switch off the cooking the cooking zone has been zone. Switch the cooking triggered zone on again Safety cut-out has been triggered and number are displayed Electronics fault Switch off the cooking zone. Switch the cooking zone on again Disconnect the appliance from the electrical supply for a few minutes (Take the fuse out of the house's wiring system) If after switching on again, is displayed again, call the customer service department Briefly shade the control panel, for example with the hand Acoustic signal sounds, appliance switches itself off Switch appliance on (again) and minus are displayed Light rays that are too strong on the control panel, for example bright sunlight 1 3 If you are unable to remedy the problem by following the above suggestions, please contact your dealer or the Customer Care Department. [. . . ] The guarantee will not apply if damage caused to delicate parts, such as glass (vitreous ceramic), synthetic materials and rubber, is the result of inappropriate use. The guarantee cannot be called on for minor faults that do not affect the value or the overall reliability of the appliance. The statutory warranty does not apply when defects are caused by: · a chemical or electrochemical reaction caused by water, · abnormal environmental conditions in general, · unsuitable operating conditions, · contact with harsh substances. The guarantee does not apply to defects due to transport which have occurred outside of our responsibility. [. . . ]