User manual AEG-ELECTROLUX DD8760M/S

[. . . ] The hot oil in the frying pan might ignite due to overheating. The risk of self-ignition increases when the oil being used is dirty. It is extremely important to note that overheating can cause a fire. Never carry out any flambé cooking under the hood. [. . . ] The control ball flashes orange to indicate the saturation of the charcoal filter even if the hood is used in the extractor version and no charcoal filter is fitted. In this case, perform the signal reset operation as follows: select the intensive speed (the control ball lights up with a red flashing light), depress again and hold depressed for about 3 seconds until an audible signal indicates the reset has taken place. 3 The control ball is a balancer switch. Depressing the control ball repeatedly towards the bottom, switches on the hood and you may select the motor level desired, depressing once again the hood switches off. depress towards the bottom to switch on the hood. Switching on the light - Fig. 3 Depress the control ball towards the top : once for submersed lighting, once again for full lighting, depress again to switch off the light. Indicator light for grease or charcoal filter The air duct, in this hood, includes a device that signals when the filter requires cleaning or changing . depress towards the top to switch on the lights Fig. 3 Led signal for grease filter The LED signal flickers (flickering green light) when the grease filter requires cleaning, occurs at about 40 operating hours. Ensure that the indicator light is checked each time the hood is used. Led signal for charcoal filter The LED signal flickers (flickering orange light) when the charcoal filter requires cleaning, occurs at about 160 operating hours. Ensure that the indicator light is checked each time the hood is used. Re-setting the saturation signal After cleaning or replacing the filter, select the intensive speed (the control ball lights up with a red flashing light), depress again and hold depressed for about 3 seconds until an audible signal indicates the reset has taken place. 61 Maintenance and care The hood must always be disconnected from the electricity supply before beginning any maintenance work. Cleaning the hood Clean the outside of the hood using a damp cloth and a mild detergent. Never use corrosive, abrasive or flammable cleaning products. Never insert pointed objects in the motors protective grid. Wash the outside surfaces using a delicate detergent solution. Use normal detergent and choose the highest temperature (65º C). Wash the filter separately so that no food parts gets stuck on the filter and later causes bad odours. To reactivate the filter, the filter should be dried in an oven for 10 minutes with a temperature of maximum 100ºC. After approximately three years of use, the charcoal filter should be replaced with a new, as the odour reduction capacity will be reduced. Fitting Fit the charcoal filter on the rear side of the grease filter, fix it with two metal wires. To remove proceed in the charcoal filter reverse order. Always specify the hood metal wires model code number and serial number when ordering replacement filters. This information is shown on the registration plate located on the inside of the unit. The charcoal filter can be ordered from your local AEG Service Force Centre. 6 grease filter 64 Warning Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. [. . . ] Remote control RM 8700* Telescopic chimney (for extractor version only)* Stainless steel side panels (Only DD 8794)* Aluminium side panels * Not available in UK. To guarantee the same quality of illumination we advise using the same type of light: 13W Phillips neon lamp (Cod. Ensure that the transparent part of the bulb is directed towards the outside to guarantee a correct diffusion of the light. Mounting accessories included 1 support bracket 1 deflector 3 Rubber strips 2 Screw caps 1 template 2 spacers 4 wood-screws 5 x 45 mm 4 wall plugs Ø 8 mm 2 metal screws 3, 5 x 9, 5 2 metal screws 3, 5 x 32 2 metal screws 5 x 18 1 reduction flange Ø 150-125 mm (DD 8794 and DD 8795 only) 2 flanges Ø 150 mm Only DD 8795 and CHDD 8795: 2 Stainless Steel side panels 68 Electrical connection (not for UK) Safety warnings for the electrician Before connecting the appliance to the power supply, check that the voltage indicated on the rating plate corresponds to the mains power supply available. Appliances fitted with a plug can be connected to any standard power socket within easy access. [. . . ]