User manual AEG-ELECTROLUX EFC9588

[. . . ] installation and user manual EFC9588X Range hood 2 contents electrolux rangehood Congratulations Congratulations and thank you for choosing our rangehood. We are sure you will find your new rangehood a pleasure to use. Before you use your rangehood, we recommend that you read through the whole user manual, which provides the description of the rangehood and its function. To avoid the risks that are always present when you use an electrical appliance it is important that the rangehood is installed correctly and that you read the safety instructions carefully to avoid misuse and hazards. [. . . ] NOTE: The height of the underside of the hood body must be a minimum of 550mm above an electric cooktop & gas cook top and a maximum height of 750mm (refer to table). * If the instructions of the hob specify a greater distance than the minimum above, then that shall be the minimum height for installation. NOTE: The fan housing exhaust outlet is 163mm in diameter. Use duct transition or flexible pipe supplied with the rangehood as a reducer if using 150mm optional ducting accessories. NOTE: For ducted mode, we recommend extending flue pipe through the roof to external "china hat" to vent exhaust externally. We do not recommend venting into ceiling cavity. NOTE: To ensure optimum performance of the rangehood, the use of rigid ducting is recommended. Rigid flexible ducting is suitable, although loose flexible ducting is unacceptable. Installation of telescopic exhaust covers Separate the inner and outer exhaust covers, and carefully remove the protective coating from both. Carefully reassemble the inner and outer exhaust covers sections by sliding the inner into the outer exhaust cover. Carefully lower the assembled inner and outer exhaust covers onto the top of the cooker hood body, and insert the exhaust cover intotherangehoodbodyapproximately5mm. Fixinner (top) exhaust cover to the mounting bracket with screws supplied. Ensure that the inner (top) section is extended. 2 arkthelocationforthewallandceilingfixingpoints M above the hood base using the hood base as the reference point. 3 Install wall and ceiling mounting with suitable screws (to support a total weight of 30kg) to the wall at the positions marked in diagram. 4 Remove the protective plastic film from the hood body and hang hood on the mounting points then secure at the anti-tilt locations as indicated in diagram. Dependingonthepreferredinstallation/ductingmode, follow step 5a or 5b below. 5a Recirculating mode(Fig. A, previouspage). Usingthe centre line, secure the mount bracket to the wall using suitable screws. Use cable ties or suitable duct tape to secure the T-piece. NOTE: When installed in recirculation mode, it is recommended to use a carbon filter (included as standard equipment with EFC9588X). OR 5b Ducted mode(Fig. B, previouspage). Therangehood hasbeensuppliedwithflexibleexhaustpipeandduct transition piece, alternatively a 150mm diameter noncombustiblefluepipecanbeused. Continuethecentre line to the ceiling. Attach the ceiling mount bracket on thecentreline. Fitpreferredfluepipetothefan transition duct. 30 (from ceiling) 100 200 100 All lines are to the centres of the holes important Care must be taken to ensure the screws are not cross threadedwhenattachingtheouterfluecover. If installed in recirculating mode, insert the carbon filter. To complete the rangehood installation, replace the filter. Placebackedgeoffilterintopositionandpushupfront edge so that the filter clips into place. [. . . ] Figure1below. caution Step 3 Unlatch the filter at each side and pull the filter towards you. Figure3below. Be very careful to keep the trough level to avoid spilling any liquidinthetrough. Step 4 Disengagethepins, eachside, atthebottomcornerofthe filterandremovethefilter. Figure4below. Moveoiltroughindirectionofarrow. Step 2 Opentheglassdoorpaneltothe"Service"position (thelaststoplocation). Figure2. [. . . ]