User manual AEG-ELECTROLUX EFP6426/XS

[. . . ] · Since the rule for rooms with fuel burning appliances is "outlet hole of the same size as the ventilation hole", a hole of 500-600 cm2, which is to say a larger hole, could reduce the performance of the extractor hood. · If the hood is used in its filtering function, it will operate simply and safely in the above conditions without the need for any of the aforementioned measures. 30 · When the hood is used in its extractor function, the following rules must be followed to obtain optimal operation: -- short and straight outlet hose -- keep bends in outlet hose to a minimum -- never install the hoses with an acute angle, they must always follow a gentle curve only -- keep the hose as large as possible (preferably the same diameter as the outlet hole). · Failure to observe these basic instructions will drastically reduce the performance and increase the noise levels of the extractor hood. for the user · Always cover lighted elements, to prevent excess heat from damaging the appliance. [. . . ] The numbers and symbols have the following meanings (Fig. 2 - from left to right): 1 2 3 4 = = = = = = = blower set 1 blower set 2 blower set 3 blower set 4 light light OFF light ON The blower is controlled by shifting the sliding switch. The extractor part (vapour catcher) of the hood is used to switch the blower on and off when the appliance is switched on (Motor). When the vapour catcher of the appliance is withdrawn (without preceding disengagement of the hood via the switches), the set fan output is automatically re-engaged. If the extractor part is re-inserted without operation of the switches, first the blower is switched off. The lighting can be separately switched on and off with the sliding switch. Turn the hood on a few minutes before you start cooking then you will get an underpressure in the kitchen. It should be left on after cooking for about 15 minutes or until all odours have disappeared. Correct ventilation If the cooker hood is to work correctly there must be an under pressure in the kitchen. It is important to keep the kitchen windows closed and have a window in an adjacent room open 32 Maintenance and care The hood must always be disconnected from the electricity supply before beginning any maintenance work. Cleaning · Warning: always disconnect the hood from the mains power supply before cleaning it. Never insert pointed objects in the motor's protective grid. · Wash the outside surfaces using a delicate detergent solution. Insert the charcoal filter into the lugs of the holding frame above using the 2 red clips to retain it below, press the red clips inwards, and insert the charcoal filter in the holding frame. Press both red lugs upwards (towards the inside of the housing) and remove the charcoal filter downwards. Clean the internal housing only with warm washing-up liquid' suds (never use any abrasive cleaners, brushes, or scouring agents). · Always specify the hood model code number and serial number when ordering replacement filters. This information is shown on the registration plate located on the inside of the unit. · The charcoal filter can be ordered from the AEG technical assistance service. Fig. 4 Changing the light bulb(s) · Disconnect the unit from the mains power supply. · Replace the old light bulb with a new light bulb of the same kind. · Replace the lamp cover support. · If the light does not come on, make sure the bulb has been screwed in correctly before contacting the technical assistance service. CLOSED CLOSED OPEN OPEN Fig. 5 34 Technical Specifications Dimensions (in cm) Height Width Depth Lighting: Grease filter Maximum absorbed power 39, 5 59, 8 27, 5 + Lichtblende (max. [. . . ] the appliance can be disconnected at need merely be removing the plug. Electrical connection 220-240 V ­ by means of fixed power cable with plug. (Fixed connection of the appliance must only be carried out by an authorised electrician. ) Installation Mounting accessories included 1 deflector 4 spacer discs 1 metal screws 2, 9x13 2 metal screws 2, 9x9, 5 2 metal screws 3x9 4 wood-screws 4, 5 x 16 mm 1 flange Ø 120 mm Preparing the wall unit - Extractor version · The hood is supplied as an extractor unit. Before installing the hood, drill a hole in the roof of the wall unit (see fig. [. . . ]