User manual AEG-ELECTROLUX EHGC77BS

[. . . ] Young children MUST NOT be allowed to tamper with the controls or play near or with the oven. This appliance has been designed for cooking edible foodstuff and to be used for domestic non-professional purposes only. It must not be used for any other purpose. It is dangerous to alter the specification in any way. [. . . ] The use of a gas cooking appliance results in the production of heat and moisture in the room in which it is installed. 9 Possibilities for insertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions: Safety Instructions Step by step instructions for an operation Hints and Tips Environmental information Description of the appliance 1 1 Ultra-Rapid Burner - 4, 0 kW 2 Burner Control Knob 2 Instruction for the User Burner Control Knob The hob burner control knob is situated on the hob front panel. The symbols on the knob mean that : there is no gas supply there is maximum gas supply / Ignition setting there is minimum gas supply Lighting the burners For easier lighting, proceed before putting a pan on the pan support. Push the relevant knob down and turn it anti-clockwise until it reaches the "maximum" position. Then, check the flame is regular and adjust it as required. 3 If you cannot light the flame even after several attempts, check the "cap" (Fig. To put the flame out, turn the knob to the symbol . In the absence of electricity, ignition can occur without the electrical device; in this case approach the burner with a flame, push the relevant knob down and turn it anti-clockwise until it reaches the "maximum" position. Always turn the flame down or put it out before taking the pans off the burner. Carefully supervise cookings with fats or oil, since these types of foodstuff can result in a fire, if overheated. A B Energy saving advices To ensure maximum burner efficiency, it is strongly recommended that you use only pots and pans with a bottom fitting the size of the burner used, so that flame will not spread beyond the bottom of the vessel (see the table beside). It is also advisable, as soon as a liquid starts boiling, to turn down the flame so that it will barely keep the liquid simmering. 2 have already been assembled in the factory. The appliance, before leaving the factory, has been tested in order to give you the best results. IMPORTANT - When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Use some soapy water, never a flame. Gas connection It is indispensible that the connection to the gas mains are carried out by means of an AGB tap. Choose fixed connections or use a flexible pipe in AGB (stainless steel). If using flexible metallic pipes, be careful they do not come in contact with mobile parts or they are not squeezed. Use the same attention when the hob is combinated with an oven. IMPORTANT - To ensure a correct operation, a saving of energy and the long-life of the appliance, the voltage pressure of the appliance must correspond to the recommended values. Before fitting the appliance ensure that the installation has the correct voltage for the appliance. At full capacity, the drop in pressure must not exceed 5%. Such a drop in pressure is caused by the following parameters: - maximum capacity of meter; - diameter and lenght of the tube in front and behind the meter; Fig. 2 FO 2365 A) Ramp with ending nut B) Seal C) Adjustable connection 6 Electrical Connection The appliance is designed to be connected to 220 / 240 V monophase electricity supply. [. . . ] The connection cable has to be placed in order that, in each part, it cannot reach a temperature 90 °C higher than the room temperature. The brown coloured phase cable (fitted in the terminal block contact marked with "L") must always be connected to the network phase. 3 Neutral Earth (yellow/green) Fig. 4 FO 0257 Replacement of the connection cable The connection of the connection cable to the appliance's terminal block is of type "Y". [. . . ]