User manual AEG-ELECTROLUX EHGF77B

[. . . ] This appliance is not connected to a combustion products evacuation device. It must be installed and connected in accordance with current installation regulations. Particular attention shall be given to the relevant requirements regarding ventilation. Ensure a good ventilation around the appliance. [. . . ] If you cannot light the flame even after several attempts, check the "cap" (Fig. To put the flame out, turn the knob to the "off" position (symbol )). 1 A B D C A - Burner cap B - Burner crown C - Ignition candle D - Thermocouple · Always turn the flame down or put it out before taking the pans off the burner. In the absence of electricity, ignition can occur without the electrical device; in this case approach the burner with a flame, push the relevant knob down and turn it anticlockwise until it reaches the "maximum" position. When switching on the mains, after installation or a power cut, it is quite normal for the spark generator to be activated automatically. 74 Using the hob correctly To ensure maximum burner efficiency, it is strongly recommended that you use only pots and pans with a bottom fitting the size of the burner used, so that flame will not spread beyond the bottom of the vessel (see the table beside and Fig. It is also advisable, as soon as a liquid starts boiling, to turn down the flame so that it will barely keep the liquid simmering. Carefully supervise cookings with fats or il, since these types of foodstuff can result in a fire, if over-heated. Prolonged cooking with potstones, earthenware pans or cast-iron plates is inadvisable. Also, do not use aluminium foil to protect the top during use. Make sure pots do not protrude over the edges of the cooktop and that they are centrally positioned on the rings in order to obtain lower gas consumption. Do not place unstable or deformed pots on the rings: they could tip over or spill their contents, causing accidents. 2 Burner Large (rapid) Small (auxiliary) minimum diameter 160 mm 80 mm maximum diameter 240 mm 160 mm 75 Cleaning and Maintenance Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. Fit the cable with a plug suitable for the load and connect it to a suitable safety socket. To connect directly to the mains, a suitable omnipolar switch with contact gap of at least 3 mm complying with current standards must be installed between the appliance and the network. The yellow/green earth wire must not be interrupted by the switch. The brown phase wire (coming from terminal "L" on the terminal block) must always be connected to the power supply phase wire. In any case the power cable must be positioned in such a way that no part of it reaches a temperature of more than 90°C. REPLACING THE POWER CABLE The connection of the connection cable to theappliance's terminal block is of type "Y". This means that its replacement requires the specific equipment ofa technician. In this case, only cable type H05V2V2-F T90 must beused. The cable section must be suitable to the voltageand the working temperature. The yellow/green earth wire must be approximately 2 cmlonger than the phase wires (Fig. After connection, test the heating elements by operating them for about 3 minutes. To open the terminal block and reach the terminals, proceed as follows: # insert the point of a screwdriver into the visible protrunding part of the terminal block; # exert a light pressure and lift (Fig. 5-b 78 Gas connection · The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force. [. . . ] The edge of the cut out must have a minimum distance from the rear wall of 55 mm. If there are side walls, or sides of the furniture unit near the hob, the cut out edges must have a minimum distance of 100 mm. R A = Rapid burner = Auxiliary burner Fitting the hob to the worktop The hob can be installed in a kitchen unit with an opening for insertion whose dimensions are shown in Fig. To install the hob, proceed as follows: 1) Place the seals supplied with the hob all around the edge of the cut out, taking care that the sealings meet without overlapping. [. . . ]