User manual AEG-ELECTROLUX EHS6940HOX

[. . . ] We promise that it will provide a superior User Experience delivering Ease-of-Mind. Good luck! 4 electrolux contents Contents Safety instructions Description of the Appliance Operating the appliance Tips on cooking and frying Cleaning and care What to do if . . . Disposal Installation Instructions Assembly Guarantee/Customer Service Service and Spare Parts 5 7 9 12 15 17 19 20 22 26 29 The following symbols are used in this user manual: 1 3 2 Important information concerning your personal safety and information on how to avoid damaging the appliance. General information and tips Environmental information safety instructions electrolux 5 Safety instructions Please comply with these instructions. [. . . ] There is the risk of burns from the appliance if used carelessly. To set the required cooking zone again, make another selection. 10 electrolux operating the appliance Using the child safety device The child safety device prevents unintentional use of the appliance. The child safety device can only be activated immediately after the appliance has been switched on. Switching on the child safety device Step 1. 2. Control panel Switch on appliance. (Do not set a heat setting. ) Touch for 5 seconds / Display (if hot) is displayed. Appliance switches off. To override or switch the child safety device off sucessfully, the steps must be performed immediately one after the other. No other sensor fields must be touched between the steps described. Overriding the child safety device The child safety device can be switched off in this way for a single cooking session; it remains activated afterwards. 2. Control panel Switch appliance on / Display (if hot) Touch the two of the front cookor ing zones at the same time Decimal points flash Until the appliance is next switched off, it can used as normal. Switching off the child safety device Step 1. 2. Control panel Switch appliance on Touch for 5 seconds / Display (if hot) or Decimal points flash Appliance switches off. operating the appliance electrolux 11 Safety cut-out Cooking surface If after switching on the appliance a heat setting is not set for a cooking zone within approx. 10 seconds, the appliance automatically switches itself off. Wipe the appliance with a damp cloth and a little washing up liquid. Rub the appliance dry using a clean cloth. Remove Type of dirt sugar, food containing sugar plastics, tin foil limescale and water rings fat splashes shiny metallic discolouration immediately yes yes ------- when the appliance has cooled down ----yes yes yes using a scraper* cleaner for glass ceramic or stainless steel* *Scrapers and cleaners for glass ceramic and stainless steel can be purchased in specialist shops, supermarkets, the parts department of your local Service Force Centre or from www. shop. electrolux. co. uk Remove stubborn residues with a cleaner for glass ceramic or stainless steel. Scratches or dark stains on the glass ceramic that cannot be removed do not however affect the functioning of the appliance. what to do if . . . electrolux 17 What to do if . . . Problem The cooking zones are not functioning. Possible cause No cooking zone selected Remedy Select cooking zone within 10 seconds of switching on (Decimal point lights up) Switch on the appliance again. Select cooking zone within 10 seconds of switching on The cooking zones cannot be More than 10 seconds has selected / Appliance does not passed since the appliance react to the control panel input was switched on The child safety device is acti- Deactivate the child safety devated vice (See section "Child safety device") The sensor fields are partly covered by a damp cloth or with liquid Safety cut-out has been triggered The residual heat indicator is not displaying anything Remove the cloth or the liquid Switch on the appliance again The cooking zone was only on If the cooking zone is supfor a short time and is therefore posed to be hot, call your local not hot Service Force Centre. Several sensor fields were touched at the same time Safety cut-out due to overheating. Appliance is incorrectly connected The overvoltage protector has been activated (for an incorrect connection see above Er25 or for overheating of the electronic components see Only touch one sensor field Let the appliance cool down. Disconnect the appliance from the electrical supply and have it connected properly Separate the appliance from the mains for a few minutes (remove the mains fuse). Let the appliance cool down. Er03 Er21 Er25 is displayed is displayed is displayed (only for 10 seconds) Er40 is displayed Er21) 18 electrolux what to do if . . . In the event of any other fault codes that arise, disconnect the appliance from the electrical supply for a few seconds (Take out the fuse from the house's wiring system). If the fault code is displayed again, please call your local Service Force Centre and report the fault code. If you are unable to remedy the problem by following the above suggestions, please contact your local Service Force Centre. Warning! [. . . ] The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by us. All service work under this guarantee must be undertaken by a Service Force Centre. Any appliance or defective part replaced shall become the Company's property. This guarantee is in addition to your statutory and other legal rights. [. . . ]