User manual AEG-ELECTROLUX EHT7333C

[. . . ] 10 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 If the gas-hob does not work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Service and spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The hob unit is intended for ordinary household cooking purposes. Any other use can result in damage to the unit as well as personal injury. Use only pots and pans with a rigid, even contact surface - uneven contact surface results not only in poor heat conduction, but also increases the risk of dangerous spills. During deep-fat frying, sauteeing, melting of butter, etc. , one must always remain near the unit, due to the danger of fire. In the event of fire the unit must be shut off immediately (and the cooker hood as well, if in use). Make sure that the unit is shut off when not in use - the knob should rest at "0". The unit becomes dangerously hot during use, and remain so for a period of time. They should therefore be treated with due respect. For hygienic and safety reasons the unit must be kept clean. Grease, oil and food spills create unpleasant odours when burnt, and can in some cases result in open flames. Read - and adhere to - the users instructions, as well as any instructions and warnings printed on the labels of the cleaning agents used. The purpose of these notches is to create space for the electrical cables. Glass cover For units with a glass cover, ensure that the cover always remains open while the unit is operating (operation indicator lamp on). 12 5 Faults Question: There is no spark when lighting the gas?Answer Check whether the 230 V connection has been plugged in. The ground fault circuit relay way have switched off. The fuse has blown The operating knob has not been depressed long enough, or has not been depressed sufficiently. Check whether the cover has been replaced correctly, e. g. after cleaning. Mounting MIN 55 Caution: In order to avoid a hazard this appliance must be installed according to these instructions for installation The hob unit can be mounted in any type of kitchen with a table surface whose thickness is between 28 mm and 40 mm. When the operating knob is released the gas ring goes out again? Headroom The distance to any shelves or tops of a cabinet under the hob is to be at least 55 mm. The gas ring burns very unevenly?? Fixing Screw the fixing brackets out to such an extent that they can be turned in under the table top. Tighten the brackets on to Minimum distance the table top with an ordinary to wall: screwdriver. 150 mm Minimum distance to wall (nonflammable material): 50 mm Cut-out measurements One rectangular hole is sawn out for the hob combination chosen. The depth of the cut-out for any unit is: 490 mm Reinforcement Length of hole = sum of all units` externally measured length, less 20 mm. beams Mounting of Reinforcement Beams A reinforcement Beam, with supporting flanges at each end, is included with each two-burner unit. For unit combinations, a reinforcement beam must be used between each unit. 6 11 Maintenance and cleaning Stainless steel surfaces Perform daily cleaning with a slightly damp cloth. [. . . ] flame Burner 2 Bruner 1 12 Guide knob for grid 10 7 Ignition Burner cover/burner ring Together with the burner ring the burner cover forms a space where the final mixture of gas and air takes place in order to make the gas burn correctly. Please note: It is consequently very important that the individual burner cover/ring is placed correctly on the burner. The burner ring has been provided with holes for the ignition electrode, and the thermo sensor. If the burner cover/ring are wrongly placed the burner will operate incorrectly, and the burners may be damaged within at short space of time. [. . . ]