User manual AEG-ELECTROLUX EWG147540W

[. . . ] EWG 147540 W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN WASHING MACHINE USER MANUAL 2 electrolux Electrolux. Thinking of you. Share more of our thinking at www. electrolux. com CONTENTS Safety information Product description Control panel First use Personalisation Daily use Helpful hints and tips Washing programmes 2 4 5 7 7 8 11 13 Care and cleaning 16 What to do if. . . [. . . ] Although biodegradable, detergents contain substances which, in large quantities, can upset the delicate balance of nature. The choice of detergent will depend on the type of fabric (delicates, woollens, cottons, etc. ), the colour, washing temperature and degree of soiling. All commonly available washing machine detergents may be used in this appliance: · powder detergents for all types of fabric · powder detergents for delicate fabrics (60°C max) and woollens · liquid detergents, preferably for low temperature wash programmes (60°C max) for all types of fabric, or special for woollens only. The detergent and any additives must be placed in the appropriate compartments of the dispenser drawer before starting the wash programme. If using liquid detergents, a programme without prewash must be selected. Your appliance incorporates a recirculation system which allows an optimal use of the concentrated detergent. Follow the product manufacturer's recommendations on quantities to use and do not exceed the «MAX» mark in the detergent dispenser drawer. DEGREES OF WATER HARDNESS Water hardness is classified in so-called "degrees" of hardness. Information on hardness of the water in your area can be obtained from the relevant water supply company, or from your local authority. A water softener must be added when water has a medium-high degree of hardness (from degree of hardness II). Follow the manufacturer's instructions. The quantity of detergent can then always be adjusted to degree of hardness I (= soft). 1) do not use acetone on artificial silk electrolux 13 Degrees of water hardness German °dH 0-7 8-14 French °T. H. 0-15 16-25 Degrees of water hardness German °dH 15-21 > 21 French °T. H. 26-37 > 37 Level Characteristic soft medium Level Characteristic hard very hard 1 2 3 4 WASHING PROGRAMMES Programme Maximum and Minimum Temperature Cycle Description Maximum Spin Speed Maximum Fabrics Load Type of Laundry -- Cotoni 90° - Cold Main wash - Rinses Maximum spin speed 1400 rpm Max. load 7 kg - Reduced load 3 kg 1) White and coloured cotton (normally soiled items). -- Cotoni + Prelavaggio 90° - Cold Prewash - Main wash - Rinses Maximum spin speed 1400 rpm Max. load 7 kg - Reduced load 3 kg 1) White or coloured cottons with prewash phase (heavily soiled items). -- Sintetici 60° - Cold Main wash - Rinses Maximum spin speed 900 rpm Max. load 3 kg - Reduced load 1. 5 kg 1) Synthetic or mixed fabrics normally soiled items. -- Sintetici + Prelavaggio 60° - Cold Prewash - Main wash - Rinses Maximum spin speed 900 rpm Max. load 3 kg - Reduced load 1. 5 kg 1) Synthetic or mixed fabrics with prewash phase (heavily soiled items). Options Detergent Compartment SPIN REDUCTION RINSE HOLD NO SPIN NIGHT CYCLE EASY IRON EXTRA RINSE TIME MANAGER SPIN REDUCTION RINSE HOLD NO SPIN NIGHT CYCLE EASY IRON EXTRA RINSE TIME MANAGER SPIN REDUCTION RINSE HOLD NO SPIN NIGHT CYCLE EASY IRON EXTRA RINSE TIME MANAGER SPIN REDUCTION RINSE HOLD NO SPIN NIGHT CYCLE EASY IRON EXTRA RINSE TIME MANAGER 2) 2) 14 electrolux Programme Maximum and Minimum Temperature Cycle Description Maximum Spin Speed Maximum Fabrics Load Type of Laundry -- Delicati 40° - Cold Main wash - Rinses Maximum spin speed 700 rpm Max. [. . . ] 4) supplied with the appliance. a) Door The dimensions of the door should be: 26 electrolux Fig. 4 A (steel disk + rubber ring) into the inner side of the door. Its position must correspond to the magnet B on the appliance (Fig. 6 A B c) Mounting the door Fix the hinges to the appliance by means of the M5x15 screws. [. . . ]