User manual AEG-ELECTROLUX HG 755420 UM

[. . . ] HG755420UM EN GAS HOB USER MANUAL GB 2 FOR PERFECT RESULTS Thank you for choosing this AEG product. We have created it to give you impeccable performance for many years, with innovative technologies that help make life simpler ­ features you might not find on ordinary appliances. Please spend a few minutes reading to get the very best from it. ACCESSORIES AND CONSUMABLES In the AEG webshop, you'll find everything you need to keep all your AEG appliances looking spotless and working perfectly. Along with a wide range of accessories designed and built to the high quality standards you would expect, from specialist cookware to cutlery baskets, from bottle holders to delicate laundry bags. . . Visit the webshop at: www. aeg. com/shop Contents 3 CONTENTS 4 6 12 13 15 16 17 18 19 Safety information Installation Product description Operation Helpful hints and tips Care and cleaning What to do if. . . [. . . ] If it is fitted below 400 mm a space of 50 mm must be allowed from the edges of the hob. For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I. S 813 Current Edition Section 7- Permitted Locations of Appliance. Gas Connection WARNING!Any gas installation must be carried out by a GAS SAFE REGISTER installer. Make sure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this instruction booklet be ignored. On the end of the shaft, which includes the G 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. 8 Installation 1 2 3 1 End of shaft with nut 2 Washer 3 Elbow Connection to the gas supply should be with either rigid or semi-rigid pipe, i. e. The connection should be suitable for connecting to R 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Make sure that the main connection pipe does not exert any strain on the hob. If you use flexible metal pipes make sure that they agree to ISO 10380 and ISO 10807 standards. Be careful they do not come in touch with mobile parts or they are not squeezed. Also be careful when the hob is put together with an oven. It is important to install the elbow correctly, with the shoulder on the end of the thread, fitted to the hob connecting pipe. Failure to ensure the correct assembly will cause leakage of gas. Make sure that the gas supply pressure of the appliance obeys the recommended values. Rigid connection: Carry out connection by using metal rigid pipes (copper with mechanical end). Injectors replacement Remove the pan supports. Remove the caps and crowns of the burner. With a socket spanner 7 remove the injectors and replace them with the ones which are necessary for the type of gas you use (see table in Technical Data section). Assemble the parts, follow the same procedure backwards. Replace the rating plate (it is near the gas supply pipe) with the one for the new type of gas supply. You can find this plate in the package supplied with the appliance. If the supply gas pressure is changeable or different from the necessary pressure, you must fit an applicable pressure adjuster on the gas supply pipe. [. . . ] Use a special cleaner for glass or stainless steel. Clean the appliance with a damp cloth and some detergent. What to do if. . . At the end rub the appliance dry with a clean cloth. 17 In order to avoid damaging the hob top pay attention when replacing the pan support. Cleaning of the spark plug This feature is obtained through a ceramic ignition candle with a metal electrode. Keep these components well clean to prevent difficult lighting and check that the burner crown holes are not obstructed. Periodic maintenance Periodically speak your local Service Force Centre to check the conditions of the gas supply pipe and the pressure adjuster, if fitted. WHAT TO DO IF. . . Problem There is no spark when lighting the gas Possible cause · There is no electrical supply Remedy · Make sure that the unit is connected and the electrical supply is switched on. [. . . ]