User manual AEG WS 9-115

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual AEG WS 9-115. We hope that this AEG WS 9-115 user guide will be useful to you.

Lastmanuals help download the user guide AEG WS 9-115.


Mode d'emploi AEG WS 9-115
Download
Manual abstract: user guide AEG WS 9-115

Detailed instructions for use are in the User's Guide.

[. . . ] Typically, the A-weighted noise levels of the tool are: Sound pressure level (K = 3 dB(A)) . Total vibration values (vector sum in the three axes) determined according to EN 60745: Surface grinding: vibration emission value ah . Abrasive Cutting-Off Operations or Wire Brushing other vibration values could occure. WARNING The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. [. . . ] M) Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body. N) Regularly clean the power tool's air vents. The motor's fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards. O) Do not operate the power tool near flammable materials. p) Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock. Kickback and Related Warnings Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory's rotation at the point of the binding. For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the wheel that is entering into the pinch point can dig into the surface of the material causing the wheel to climb out or kick out. The wheel may either jump toward or away from the operator, depending on direction of the wheel's movement at the point of pinching. Wheel intended for larger power tool is not suitable for the higher speed of a smaller tool and may burst. additional Safety Warnings Specific for Abrasive CuttingOff Operations: a) Do not "jam" the cut-off wheel or apply excessive pressure. Do not attempt to make an excessive depth of cut. overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage. B) Do not position your body in line with and behind the rotating wheel. When the wheel, at the point of operation, is moving away from your body, the possible kickback may propel the spinning wheel and the power tool directly at you. C) When wheel is binding or when interrupting a cut for any reason, switch off the power tool and hold the power Tool motionless until the wheel comes to a complete stop. Never attempt to remove the cut-off wheel from the cut while the wheel is in motion otherwise kickback may occur. Let the wheel reach full speed and carefully reenter the cut. The wheel may bind, walk up or kickback if the power tool is restarted in the workpiece. E) Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback. [. . . ] Take care that no persons are endangered. Because of the danger of fire, no combustible materials should be located in the vicinity (spark flight zone). Due care should be taken that no sparks or sanding dust flying from the workpiece come into contact with you. When separating stone the guide shoe must be used! [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE AEG WS 9-115

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual AEG WS 9-115 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag