User manual AIRLIVE WLA-5200AP

[. . . ] WLA-5200AP 802. 11a/b/g Multi-function Wireless Access Point User's Manual Declaration of Conformity We, Manufacturer/Importer OvisLink Corp. 5F. , NO. 6, Lane 130, Min-Chuan Rd. , Hsin-Tien City, Taipei County, Taiwan Declare that the product 802. 11a/b/g Multi-function Wireless Access Point WLA-5200AP is in conformity with In accordance with 89/336 EEC-EMC Directive and 1999/5 EC-R & TTE Directive Clause EN 301 893 v1. 2. 3 (2003-08) Description Broadband Radio Access Network(BRAN); 5GHz high performance RLAN; Harmonized EN Covering essential requirements of Article 3. 2 of the R&TTE Directive. Electromagnetic compatibility and Radio spectrum matters (ERM); Wideband transmission equipment operating in the 2. 4GHz ISM band And using spread spectrum modulation techniques; Part 1: technical Characteristics and test conditions Part2 Harmonized EN covering Essential requirements under article 3. 2 of the R&TTE Directive Electromagnetic compatibility and Radio spectrum Matters (ERM); Electromagnetic compatibility(EMC) standard for radio equipment And services; Part 17Specific conditions for Wideband data and HIPERLAN equipment Generic standard to demonstrate the compliance of low power Electronic and electrical apparatus with the basic restrictions related to human exposure to electromagnetic field (10MHz ­ 300GHz) -General public Safety for information technology equipment including electrical Business equipment EN 300 328 v1. 6. 1 (2004-11) EN 301 489-1 v1. 5. 1 (2004-11) EN 301 489-17 v1. 2. 1 (2002-08) EN 50371:2002 EN 60950-1:2001/ A11:2004 CE marking Manufacturer/Importer Signature Name Position/ Title : Albert Yeh Vice President (Stamp) Date 2007/5/29 WLA-5200AP CE Declaration Statement Country cs Cesky [Czech] Declaration OvisLink Corp. tímto prohlasuje, ze tento WLA-5200AP je ve shod se základními pozadavky a dalsími píslusnými ustanoveními smrnice 1999/5/ES. [. . . ] When Auto is enabled the transmission rate will select the optimal rate. If obstacles or interference are present, the system will automatically fall back to a lower rate. A preamble is a signal used in wireless environment to synchronize the transmitting timing including Synchronization and Start frame delimiter. In a "noisy" network environment, the Preamble Type should be set to Long Preamble. The Short Preamble is intended for applications where minimum overhead and maximum performance is desired. If in a "noisy" network environment, the performance will be decreased. Select the check box to enable the Tx Burst function. The 802. 11g standard includes a protection mechanism to ensure mixed 802. 11b and 802. 11g operations. If there is no such kind of mechanism exists, the two kinds of standards may mutually interfere and decrease network's performance. 20 WLA-5200AP v2 User's Manual Enable Watch Watch Interval Watch Host Apply Change Reset Dog Check the box to enable this watch dog function and set the Watch dog time Interval (1~60 mins) and type the ip address of the host ip Press to save the new settings on the screen. Press to discard the data you have entered since last time you press Apply Change. Security (AP/Client/WISP Mode) Here you can configure the security of your wireless network. Selecting different method will enable you to have different level of security. Please note that by using any encryption, by which data packet is encrypted before transmission to prevent data packets from being eavesdropped by unrelated people, there may be a significant degradation of the data throughput on the wireless link. Authentication Type: Open System or Shared Key/Shared Key/Open System If Open System or Shared Key/Shared Key/Open System is selected, users will have to Set WEP keys with an encryption either WEP64 or WEP128. Only the Open System can set the encryption to None (Without any WEP Key protection mechanism) · HEX: If you are using hexadecimal numbers (0-9, or A-F). · ASCII: If you are using ASCII characters (case-sensitive). · Ten hexadecimal digits or five ASCII characters are needed if 64-bit WEP is used · 26 hexadecimal digits or 13 ASCII characters are needed if 128-bit WEP is used 21 WLA-5200AP v2 User's Manual Authentication Type: WPA-PSK/WPA2-PSK If WPA-PSK/WPA2-PSK is selected, users will have to select the Encryption from the pull-down list, TKIP, AES or TKIP_AES and then enter a passphrase. 22 WLA-5200AP v2 User's Manual Bridge Mode Setting Alias Name The distinguishing name of this device, you may change the default alias name by entering a new one in this column. Disable Wireless LAN Check the box to disable the Wireless LAN Interface, by so doing, you won't be able to Interface make wireless connection with this Access Point in the network you are located. In other words, this device will not be visible by any wireless station. Band · 11b/g mixed: Select to allow both wireless-b and wireless-g devices on the network. · 11B only: Select to allow only wirelessB devices on the network. · 11G only: Select to allow only wirelessG devices on the network. · 11A (indoor): Select to allow only wireless-A devices on the indoor network. · 11A (outdoor): Select to allow only wireless-G devices on the network. · 11A (indoor): Select to allow only wireless-A devices on the outdoor network. 23 WLA-5200AP v2 User's Manual Channel Number Allow user to set the channel manually or automatically. [. . . ] Server: Select to enable DHCP server function. 253 IP addresses continuing from 192. 168. 1. 1 to 192. 168. 1. 253 Click to show Active DHCP Client table. You can specify the MAC address of your Access Point to replace the factory setting. 41 WLA-5200AP v2 User's Manual Apply Changes Reset Press to save the new settings on the screen. Press to discard the data you have entered since last time you press Apply Change. Other Upgrade Firmware 1. [. . . ]