User manual AIRLIVE WMU-6000FS

[. . . ] WMU-6000FS Portable Wireless AP Storage User's Manual 1 Copyright The contents of this publication may not be reproduced in any part or as a whole, stored, transcribed in an information retrieval system, translated into any language, or transmitted in any form or by any means, mechanical, magnetic, electronic, optical, photocopying, manual, or otherwise, without the prior written permission. Trademarks All products, company, brand names are trademarks or registered trademarks of their respective companies. They are used for identification purpose only. Specifications are subject to be changed without prior notice. [. . . ] This helps control traffic flow through an access point, especially one with many clients. The setting value range is from 1 to 2347, and default value is set to 2347. 42 AirLive WMU-6000FS User's Manual Fragmentation: In a network, the maximum size or length of a fragment is determined by the protocol used to transport the data. This value should remain at its default setting of 2346. If you experience a high packet error rate, you may slightly increase your "Fragmentation" value within the value range of 256 to 2346, even number only. Setting the Fragmentation value too low may result in poor performance. DTM interval: A Delivery Traffic Indication Message (DTIM) is a countdown informing clients of the next window for listening to broadcast and multicast messages. When the Access Point has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. AP clients hear the beacons and awaken to receive the broadcast and multicast messages. The default value for DTIM interval is set to 3. Preamble Type: The Preamble Type defines the length of the CRC (Cyclic Redundancy Check) block for communication between the Access Point and roaming wireless adapters. SSID Broadcast: Enable or Disable a SSID broadcast. When enabled, the SSID of WMU-6000FS is sent to wireless enabled devices on the LAN. Press "Next" button, you could see the Wireless MAC Filtering setting. 43 AirLive WMU-6000FS User's Manual The default setting is "Disable Mac filtering", every wireless client could connect to this AP. When you select "ALL accept", the wireless clients with the MAC addresses you enter bellow will be accepted to connect to this AP, the others will be rejected. When you select "ALL Reject", the wireless clients with the MAC addresses you enter bellow will be rejected to connect to this AP, the others will be accepted. After press "Save" button, WMU-6000FS would show you this page about the wireless settings you have done. 44 AirLive WMU-6000FS User's Manual 3. 2. 2. 2 Wireless client mode Select the "Wireless client mode" and click "Go" to set up under the Wireless client mode. After entering the Wireless client mode setting, click the AP List icon to set up the AP connecting list. 45 AirLive WMU-6000FS User's Manual Click the "Scan AP" to scan the existing AP list. Select the AP you want to connect and click "Add" to set up the AP list. Select the AP you want to connect and click "Add" to set up the AP list. Click "Mod" to specify the AP information. After clicking the "Mod" button, you 46 AirLive WMU-6000FS User's Manual will find the following information and modify it depending on your actual wireless environment; this should be done necessarily when you are in the secured wireless network with WEP. Click the "Next" for advanced setting, or click "Save" or "Undo" for your need. 47 AirLive WMU-6000FS User's Manual The advanced setting items are shown as below: For the meanings of above items, please refer to "Advanced setting". After saving the values of client mode, you have to go back the "Wireless Client mode Basic Setting" page and click "Save" on the top of the page. Then you could check the settings that you have done. 3. 2. 2. 3 WDS Hybrid mode Select the "WDS Hybrid mode" and click "Go" to set up After entering the WDS Hybrid mode setting, click the AP List icon to set up the AP connecting list. Then click the "AP Setting" icon and set up the AP. 48 AirLive WMU-6000FS User's Manual NOTE: You MUST use the same channel with the AP you want to bridge. [. . . ] PC2 choose the SSID of DUT as the Access Point. Set authentication type of wireless client and RADIUS server both to PEAP_TLS. Disable the wireless connection and enable again. The DUT will send the user's certificate to the RADIUS server, and then send the message of authentication result to PC2. [. . . ]