User manual AIRTRONICS MX-3

[. . . ] Install the battery cover in place and slide to close. WARNING: Improper installation of transmitter batteries can cause serious damage to your system. A B Throttle Trigger Position Gauge Throttle Trigger Adjustment screw NOTE: Trigger Set Screw must be loosened before adjusting RECEIVER AND SERVO CONNECTIONS Your MX-3 Computer R/C system receiver is NOT equipped with BEC circuitry. DO NOT use more than 6. 0 volts to power the receiver. Anything higher than 6. 0 volts will burn-up or destroy your receiver. Only use a 4. 8~6. 0 volt battery pack or a speed controller that is designed to lower the voltage to the receiver. [. . . ] Make sure all the receiver and servo connections are tight. WARNINGS: DO NOT OPERATE YOUR SYSTEM IF SOMEONE ELSE IS ON YOUR FREQUENCE AT THE SAME TIME. YOUR MODEL CAN CAUSE SERIOUS DAMAGE OR INJURY SO PLEASE USE CAUTION AND COURTESY AT ALL TIMES. DO NOT EXPOSE THE RADIO SYSTEM TO WATER OR EXCESSIVE MOISTURE. PLEASE WATER PROOF THE RECEIVER AND SERVOS BY PLACING THEM IN A WATER TIGHT RADIO BOX WHEN OPERATING R/C BOAT MODELS. IF YOU HAVE LITTLE OR NO EXPERIENCE OPERATING R/C MODELS, WE STRONGLY RECOMMEND YOU SEEK THE ASSISTANCE OF EXPERIENCED MODELERS OR YOUR LOCAL HOBBY SHOP FOR GUIDANCE. TH D/R EPA ARC MODEL SUB-T REV H BATT MODEL L L R ST MENU MX-3 - + INC / DEC DIGITAL CONTROL SYSTEM ! B/DSC B/ DSC 3 2 1 CAUTION 92836 75 FM Super Micro 3 CH. Receiver Switch AA Dry Cell Battery Holder Mechanical Speed Controller To Battery #1 #2 #3 To Motor Steering Throttle AUX When installing your MX-3 radio system in your model, always make sure to set your model on a stand so the wheels are free from any traction before turning on your radio and or connecting your motor for the first time. REGISTRATION NUMBER The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment. 3 Channel Computer Radio System Switch B/ DSC 3 2 1 To Battery #2 To Motor 92836 75 FM Super Micro 3 CH. Receiver Electronic Speed Controller ESC ESC MX-3 To Open slide Cover Install Batteries To Close slide cover The Throttle Trigger can be adjusted to give you a more natural feel of the throttle. Mhz Mhz LCD DISPLAY SCREENS We appreciate your purchase of this new Airtronics MX-3 Radio Control System. These instructions are intended to familiarize you with the many unique features of this modern, state of the art equipment. Please read them carefully so you may obtain maximum success and enjoyment from its operation. Please note that the MX-3 is designed for comfort and precise control of all types of model cars and boats. We wish you the best of success with your radio system. Enjoy and have fun. H TH D/R EPA ARC MODEL SUB-T REV Battery MODEL BATT Servo Movement Servo Movement Servo Movement L L V L -100 0 R -100 L -100 0 R -100 0 H -100 Servo Movement 9. 8 5 R ST Pressing both menu buttons simultaneously, will automatically move the cursor to the battery voltage screen. Low battery warning beep will come on when battery reaches 9. 1V Negative Steering ARC Faster servo movement in center, slower after ARC percentage R 100 Positive Steering ARC Slower servo movement in center, faster after ARC percentage R 100 Negative Throttle ARC Faster servo movement in center, slower after ARC percentage L 100 Positive Throttle ARC Slower servo movement in center, faster after ARC percentage L 100 0 H 100 H TH D/R EPA ARC MODEL SUB-T REV Servo Reverse MODEL Default ST TH AUX NOR NOR NOR MX-3 SYSTEM FEATURES Screen Display Unique and functional pistol grip transmitter design Well balanced for precise control Non-slip rubber steering wheel Well placed digital trim levers Optimum third channel switch location Big LCD display Adjustable (70/30) Throttle trigger Low Battery warning Quick access transmitter crystal High performance micro 3 channel receiver High torque / high speed 94102Z servo Receiver dry battery holder Switch harness NiCd charger jack in transmitter Wrist strap holder (optional wrist strap part # 99104 ) Sound Beep ( On / Off ) Digital Trim indicators (throttle and steering) Battery Fuel Tank Dual Rate Steering EPA Steering, Throttle, AUX ARC Steering, Throttle Model Memory (5) Sub-Trim Steering, Throttle Servo Rev Steering, Throttle, AUX Battery Voltage Display Audio On / Off ST TH AUX L L BATT NOR 5 R ST Press the left menu key to move the cursor to the REV screen. Change the servo direction by pressing (INC or DEC) key for the AUX channel. By pressing the left menu key again, you can change the TH and ST directions. L 100 Stick Movement 0 L 100 Stick Movement 0 H 100 Stick Movement 0 H 100 Stick Movement 0 ARC Steering Default ST TH 0 0 ARC Throttle Antenna Fully extend antenna before operating H TH D/R EPA ARC MODEL SUB-T REV Sub Trim MODEL ST TH L L BATT 05 R Press the left menu key to move the cursor to the SUB-T screen. Adjust the sub-trim by using the (INC or DEC) key. Press the left menu key to display the ST and adjust using the (INC or DEC) key. Steering Dual Rate Range +15 ~ -15 Move lever left to increase and right to decrease ST H TH D/R EPA ARC MODEL SUB-T REV Model Select MODEL LCD Display Digital Steering Trim Digital Throttle Trim BATT L L 5 R 5 ST Press the left menu key to move the cursor to MODEL. The screen will now display the model number you are currently using. [. . . ] At 6. 0V for 60 deg rotation 53 in/oz at 6. 0V H TH D/R EPA ARC MODEL SUB-T REV Steering Dual Rate MODEL Default DIGITAL CONTROL SYSTEM ST L L BATT 90 5 % R ST Press the left menu key to move the cursor to EPA. This will display your current Steering Dual Rate setting. You can change this setting by using the (INC or DEC) keys or, by moving the D/R lever located above the steering wheel. Range 0% ~ 120% NiCd Charging Inlet Increase / Decrease Keys Trigger 70, 30 70% High, 30% Low. [. . . ]