User manual AIWA HV-FX7800

[. . . ] Check that the unit's operating voltage is identical with your local power supply. · To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus. · The player is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the player itself has been turned off. Installing · Do not install the unit in an inclined position. [. . . ] If the setup menu has been displayed, first exit the setup menu. Press a and use the numeric buttons to enter the 6-digit number "210499". The current password is cleared. 30 Before Operation ­ DVD Part (Continued) Country Code After specifying the restriction level in the previous "Rating" section, set the country code so that the set restriction level is adjusted to the cinema rating system of the country where the DVD disc was produced. 1 Select Country Code on the setup menu using i+/k­, then press l. Disc Audio Disc Subtitle Disc Menu Rating Country Code TV Aspect Menu Language Progressive Scan Digital Audio Output Others Code Set US 2 3 Carry out step 2 of "Rating" on the previous page. Press i+/k­ to select the first character of the country code and press l. Refer to the country code list on pages 54 and 55. Press i+/k­ to select the second character of the country code and press OK/ENTER. 4 To change the country code Follow the above steps again. 31 PREPARATION Operation with Tape 1 z TV/VIDEO CLOCK/ COUNTER I/6 INPUT SELECT REC. END SERCH OK/ENTER, CH/TRACKING i+/k­, j/l sSTOP wREC t (SLOWT) C CLEAR Make sure that you have correctly connected the unit as described earlier in this book. Press I/6 to turn on the unit, then insert the video cassette into the unit. · The video cassette should have the window side facing up and the arrow facing away from you. i/SETUP aPAUSE/ FRAMEF r 2 3 Press C to start playing your tape. · If you load a video cassette which has had its record protection tab removed, playback of the cassette will start automatically. Numeric buttons Press aPAUSE/FRAMEF to still a picture. Press aPAUSE/FRAMEF repeatedly to advance the tape frame by frame. · Tapes can be paused for up to 5 minutes. After 5 minutes the unit will stop the tape to prevent damaging the tape or the unit. · Still picture quality can be improved slightly by pressing CH/TRACKING i+/k­. AUDIO C. LOCK SP/LP CM SKIP SHOWVIEW 4 Slow motion: During still picture hold down t (SLOWT). If you wish to record directly from the EURO AV1/ 2 or AV 3 IN jacks repeatedly press INPUT SELECT until the jack you wish to record from is displayed. AV 1 for recording from EURO AV1 AUDIO/ VIDEO jack on the rear of the unit. AV 2 for recording from EURO AV2 DECODER jack on the rear of the unit. AV 3 for recording from AV 3 IN VIDEO and AUDIO (Left & Right) jacks on the front of the unit. Press SP/LP if you wish to record in Long Play or Standard Play. · SP will produce improved picture and sound quality, however LP will provide twice as much recording time as SP. 12 REC f OSD ON OFF PSET R Pr12 ACMS + - TIME DATE SYSTEM NIC AB C OSD OPR 4 OK i 16:9 4:3 DECODER OPR 2 Press i+/k­ to select: OFF, SOFT or SHARP. PSET RECSOFT R OFF 12 Pr-12 ACMS - + f OSDSHARP TIME DATE SYSTEM NIC AB C OSD OPR ON OFF 16:9 4:3 DECODER OPR i 5 3 Press i/SETUP to return to the normal screen. Note OPR is automatically set to off when a cassette is ejected or the power is turned off. 6 Press wREC to start recording. Each successive press will increase the record time by 30 minutes until you reach a maximum of 9 hours. 33 OPERATION Operation with Tape (Continued) To pause while recording Press aPAUSE/FRAMEF to avoid recording unwanted scenes. Press aPAUSE/FRAMEF to continue recording. · Tapes can be paused for up to 5 minutes; RECP will be displayed when a tape is paused. After 5 minutes the unit will stop recording to prevent damaging the tape or the unit. 4 Press i+/k­ to select the recording type. DAILY: To record every day (except Saturday and Sunday) at the same time. WEEKLY: To record at the same time every week. Press the numeric buttons to enter the ShowView Code of the TV program that you wish to record. · If you make a mistake press j then enter the revised number. 5 To stop recording Press sSTOP. [. . . ] · The audio output options setting is wrong. The playback picture is poor. The unit does not start playback. · The disc is dirty. · Tape is a rental or was recorded on another VCR. · An unplayable disc is inserted. · The disc is placed upside down. [. . . ]