User manual AKAI GX-F620 SERVICE MANUAL

[. . . ] 4 5 5 5 Operating two or more handsets at one base station . 10 Making conference calls (3-way conversation) . 10 Call waiting during an internal call . 11 Entering HANDSET SETUP or BASE SETUP menu . [. . . ] This is normal. j Press during edit mode to insert the pause. The display shows a P for each pause inserted. Operating two or more handsets at one base station You can register up to four handsets at one base station. This allows you to make costfree internal calls between handsets or enquiry calls and conference calls. You can also forward external calls to another handset. The external user is put on hold. ~ R Press longer than one second. The external user is put on hold. ~ Enter the internal call number. When the user answers, you can announce the call. Note: You can forward the call without waiting. If the internal user does not answer, the call automatically returns after 30 seconds waiting time. Enter the internal call number. interconnect the 3-way conversation. P Press longer than one second to Note: During the conversation, the INT icon is blinking. a Press to forward the call. R Press longer than one second to Internal enquiry / toggling You are conducting a call with an external user. You can call an other internal user to conduct an enquiry call without clearing down the initial connection. You are automatically reconnected to the external connection when you end the enquiry call. nected to the internal user. toggle between the internal and the external connection. The display shows P :H3 nnnn---- blinking. The display shows the available handset numbers when linked to the base station. Note: If four handsets are registered at the base station, no further handset can be registered. You will hear the ERROR beep and the handset returns to the idle display. ~ Register Dialon GX-F620 handset at a base station N One Dialon GX-F620 handset can be registered to only one base station. up to four handsets. N One Dialon GX-F620 base station can register Enter one of the handset numbers. If the registration was successful, the idle display shows the new handset number. 13 Modify handset PIN To protect your handset settings from unintentional access you should change your handset PIN (personal identification number). Note: The factory setting of the PIN is 0000. If you do not change this setting, you enter directly the HANDSET SETUP menu. BASE SETUP menu Set base station ringer volume You can choose from four ringer volumes: 2 Press. 1 below). ~ i Press. If necessary, enter base station PIN. i Press. 1 Press. ~ ~ If necessary, enter handset PIN. Enter the handset PIN (4 digits). 5 Press. c Press to confirm. q Select the ringer volume (see table c Press to confirm. Display shows P :ç 11 0 P :ç 11 1 P :ç 11 2 P :ç 11 3 Volume setting Ringer OFF LOW MEDIUM HIGH Delete phone book / redial memory You can delete the entire handset memory. i Press. [. . . ] E. g. : press i1 [handset PIN] 11 to enter the handset RINGER VOLUME settings. After each step the handset display shows where you are in the menu tree. RINGER MELODY 1 MELODY 1: MELODY 2: MELODY 3: P :H 1 P :H 1 P :H 1 2 P :H 12 P :H 12 P :H 12 q P :H 12 P :H 12 P :H 12 1 2 3 MAIN MENU table To enter the HANDSET SETUP or the BASE SETUP menu: HANDSET SETUP: i P: EARPIECE VOLUME 1 LOW: MEDIUM: HIGH: P :H 1 P :H 1 P :H 1 I P :H 13 P :H 13 P :H 13 q P :H 13 P :H 13 P :H 13 1 2 3 1 P :H ---- If PIN is not 0000, enter handset PIN P :H BASE SETUP: i P: KEY BEEP If PIN is not 0000, enter base PIN P :ç OFF: ON: 2 P :ç ---- 1 P :H 1 P :H 1 4 P :H 14 P :H 14 q P :H 14 P :H 14 0 1 Note: The factory setting of the PIN is 0000. If you do not change this setting, you enter directly the HANDSET SETUP or BASE SETUP menu. If the PIN does not match, the handset returns to the idle state. AUTO TALK MODE 2 OFF: ON: P :H 2 P :H 2 q P :H 2 P :H 2 0 1 HANDSET SETUP menu table When you are in the HANDSET SETUP menu, you can access the following settings by pressing the keys shown in the following tables. [. . . ]