User manual AKAI LCT2716

[. . . ] Safety Guidelines Caution: Always use a power cable is properly grounded. Please use the AC cords listed below for each area: USA . . . . . . . . . . . . . . . . . . . . . . CSA/cUL FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] (Continued on next page) 17 OTHER OPERATION USING THE POP DOUBLE-WINDOW FEATURE - RECALL : Press to switch between present channel and previous channel. Note: If the previous channel is a locked channel, it display blue background and lock information. FREEZE: Press it to hold the current video and press again to cancel and return to normal viewing. FREEZE DISPLAY ZOOM : Press it repeatedly the size of image will change cycling in following sequence: 2 times 4 times 8 times 16 times 32 times 1/32 times 1/16 times 1/8 times 1/4 times 1/2 times normal. DISPLAY: Press once to display the information as following, and disappear after 3 second; When in TV mode 68 CD FREEZE RECALL ZOOM - When in VGA mode VGA 640 x 480 60Hz (Continued on next page) 18 6. 4 Using the POP double-window feature The POP (picture-out-picture) feature splits the screen into a double window that allows you to watch two programs at the same time. The POP program can come from a TV broadcast or an external source, such as a VCR. To display a TV broadcast in the POP window: 1. Press PIP button to enter the POP window. Press PIP for selecting the different PIP modes, such as following; Normal Picture PIP SOURCE Basic PIP Mode LR POP Mode Use / to select the window and active it with a red-colored frame. Press SOURCE to select the input source for the POP window. To change the next programmed channels, press number buttons (0~9) or CH+/CH-. Note: a. If the V-CHIP feature is active and you try to watch a TV program that exceeds your set rating limits, the program will be blocked. For active window, you can change channels, adjust volume, select input source ect. . After power off, the active window will be keep the setting when you power on next time. It is must to have second video source connected for basic PIP and L/R POP modes. After you choose the POP mode, all settings are only aimed at the active window. (Continued on next page) 19 USING THE POP DOUBLE-WINDOW FEATURE OSD OPTION ADJUSTMENT OSD FUNCTIONS To display a picture from an external source in the POP window: 1. (refer to Connect Accessory Devices page). Select the TV program you want to watch in the main window. Repeatedly press SOURCE to select the input source for the POP window. To change the PIP picture size: Press PIP SIZE button to select the PIP picture size, such as: Small, Middle, Large. To change the PIP position: Press PIP POS button to change the PIP window position under PIP mode, it display as following; Right Down Left Down Left Up Right Up Right Down PIP SIZE PIP POS Left Up Right Up ENTER Left Down Right Down Switching the pictures: When in Basic PIP mode, press "ENTER" to swap main or sub pictures; When in LR POP mode, press "ENTER" swap the L/R pictures. When the red frame is displaying in main window, the sound goes out of main window source. If it display in sub window, the sound goes out of sub window source. To change Main or Sub sound: 6. 5 OSD Option Adjustment Learning about the menu system After you have installed the batteries and programmed the remote control, you will need to set some preferences on the TV using the menu system. You can access the menu using the buttons on your TV or remote control. The OSD menu displayed in the following sequence (circular display): Video Audio Misc TV Geometric (Continued on next page) 20 Press MENU to display the menu system. Press ENTER on the remote control or SOURCE on the TV control panel to activate the function settings in the menu. [. . . ] (Continued on next page) 46 Symptom Power cannot be turned on. (Power indicator does not light) No Input Signal message appears. Solution - Check that both ends of the power cable are plugged into the socket appropriately. - Check that the signal line is connected properly. - Check that the power of the relevant peripherals is turned on. [. . . ]